Panasonic PanaXSeries MN1030 Series User Manual Download Page 53

Page: 53 / 340

Chapter 3 Introduction to Operation

Conditional Assembly and Linking 41

In the previous file, you either deleted the define line or made it into a comment, so you can use it to

once again select the true condition.

as103 -D DEBUG program5.asm

ld103 -m -T_CODE=40000000 program5.rf

as103 -l -a m103.map -D DEBUG program5.asm

D option

Option to specify an identifier (DEBUG), having the same effect as specifying define

DEBUG in the source file.

The contents of the final list file program5.lst are as follows.

Note that the symbol table is not displayed.

Line number 14 was assembled. Check for yourself that omitting -D DEBUG will assemble line

number 16 instead. This technique enables the programmer to freely choose assembly conditions with

command option specifications.

There is also an assembler option for suppressing the source code lines not selected during conditional

assembly. For further details, see Chapter 5 "Using the Assembler" and Chapter 6 "Using the Linker."

program5.lst Page 1

*** PanaX series Series MN1030 Cross Assembler ***

Loc

Object

Line

Source

#define

DEBUG

dat_set

macro

adr, dat

mov

adr, A0

mov

dat, D0

mov

D0, (A0)

endm

_CODE

section

CODE, PUBLIC, 1

40000000

main

#ifdef

DEBUG

M14

dat_set

data1, 0x11

40000000

FCDC0CC000040

14+

mov

data1, A0

40000006

8011

14+

mov

0x11, D0

40000008

14+

mov

D0, (A0)

#else

16X

dat_set

data1, 0x22

#endif

_DATA

section

DATA, PUBLIC, 4

4000000c

00000000

data1

40000010

00000000

data2

end

Summary of Contents for PanaXSeries MN1030 Series





















































































































































































































































































































































Search results

Summary of Contents for PanaXSeries MN1030 Series

Reviews:

Brands by name

Popular brands

Panasonic PanaXSeries MN1030 Series, User Manual

Search results

Summary of Contents for PanaXSeries MN1030 Series

Reviews:

Brands by name

Popular brands