![background image](http://html.mh-extra.com/html/panasonic/panafax-uf-7000/panafax-uf-7000_service-manual_257254079.webp)
79
UF-7000/8000
APR 2007
Ver. 2.1
UF-7100/8100
3) Preparing the Master Firmware SD Memory Card
1. Insert the SD Memory Card (32 MB to 512 MB) into the SD Memory Card Slot.
2. Perform the SD Memory Card Firmware Writing Tool.
3. After all firmware codes are copied, remove the SD Memory Card from the Slot.
The SD Memory Card is now ready to use for firmware update.
(Refer to the Local Firmware Update Tool OI on the CD and the SD Memory Card Firmware Writing
Tool OI.)
3.5.6.
Formatting the SD Memory Card
To make the Master Firmware SD Card, format the Card first by following the steps below. If the Card will be
used to update the Firmware of other machines, format the Card first with the Service Mode F9-15.
Caution:
Do not remove the SD Memory Card or turn the power OFF during Formatting or while Updating the
Firmware.
Note:
The Master Firmware SD Card can be installed or removed without turning the power OFF,
however, an SD Memory Card formatted for DATA requires the power to be cycled OFF and ON
after its installation or removal.
1) When a DATA SD Card is Not installed
1. Turn the Power Switch on the back of the machine to the OFF position. (During a Lightning Storm,
to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power
Cord.)
2. Disconnect the Telephone Line, LAN and/or USB Cables.
3. Turn the Power Switch on the back of the machine to the ON position.
4. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.
5. Enter the Service Mode F9-15 (SD Card Format).
6. Install the SD Card into the machine.
7. Perform the Service Mode F9-15 (SD Card Format).
8. After the SD Card is formatted, the machine goes to Service Mode F9.
9. Remove the SD Memory Card from the machine.
10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys sequentially to return to standby.
11. Turn the Power Switch on the back of the machine to the OFF position.
12. Reconnect the Telephone Line, LAN and/or USB Cables.
13. Turn the Power Switch on the back of the machine to the ON position.
Note:
Repeat steps 5 to 9 to continue formatting other SD Card(s).
2) When a DATA SD Card is installed
1. Turn the Power Switch on the back of the machine to the OFF position. (During a Lightning Storm,
to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power
Cord.)
2. Disconnect the Telephone Line, LAN and/or USB Cables.
3. Turn the Power Switch on the back of the machine to the ON position.
4. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.
5. Remove the
DATA SD Card
from the machine.
6. Enter the Service Mode F9-15 (SD Card Format).
7. Install the SD Card into the machine.
8. Perform the Service Mode F9-15 (SD Card Format).
9. After the SD Card is formatted, the machine goes to Service Mode F9.
10. Remove the SD Memory Card from the machine.
11. Reinstall the
DATA SD Card
into the machine.
Summary of Contents for Panafax UF-7000
