background image

  1

Panasonic Over The Range Microwave Oven

INSTALLATION INSTRUCTIONS

Read carefully and keep these installation instructions

A   REQUIREMENTS FOR INSTALLATION

Installation of this product is safest and easiest when performed by two people. Before beginning the 
installation, please read the following requirements to make sure you have everything you need to safely 
install this product.

1.  SUPPLY CIRCUIT AND GROUNDING REQUIREMENTS

 

This oven must be plugged into a 15 AMP or 20 AMP, 120 volt, 60 Hz, 3 prong grounded outlet. The outlet 
must be connected to a separate 15 AMP or 20 AMP circuit of the proper voltage and frequency. No other 
appliance should share the circuit. Wire size must conform to the requirements of the National Electric Code 
or the prevailing local code for this kilowatt rating.

 

The recommended location for this outlet is inside the cabinet directly above where the oven is going to be 
installed. This location is desirable because the power supply cord on the product is short. If an outlet is 
not readily available, one should be installed by a quali

fi

ed electrician and should conform to the National 

Electric Code or the prevailing local code.

 

The installer must perform a ground continuity check on the outlet box to ensure that it is properly 
grounded, and if it does not meet the electrical requirements of the product a quali

fi

ed electrician should be 

employed to correct any de

fi

ciencies.

2.  MOUNTING SURFACE WEIGHT CAPACITY REQUIREMENTS

 

FOR PERSONAL SAFETY, ANY MOUNTING SURFACE FOR THIS PRODUCT MUST BE CAPABLE OF 
SUPPORTING THE PRODUCT’S WEIGHT OF 55 lbs. (25 kg). PLUS ADDITIONAL OVEN LOADS OF UP 
TO 22 lbs. (10 kg). FOR A TOTAL WEIGHT OF 77 lbs. (35 kg).

 

Proper installation of this product requires that the product be partially supported by the bottom surface of 
the cabinet directly above the mounting location. Therefore reinforcing this bottom might be necessary if the 
cabinet cannot support the weight requirement mentioned above.

3.  MOUNTING SPACE REQUIREMENT

 

Kitchen cabinet depth must be at least 12" (30.5 cm) and not 
over 13" (33 cm).

 

A minimum width of 30" (76 cm) is required on a 

fl

at, vertical 

wall for installation of this product.

 

This product is suitable for use above gas or electric cooking 
equipment 36 in. or less. To reduce the risk of 

fi

re or electric 

shock, install the oven at the clearance "H" speci

fi

ed below: 

(Fig. A-1)
• Electric 

range: 

 

H = 13

5

/

8

" (34.6 cm) MINIMUM

• Gas 

range:

 

H = 16" (40.6 cm) MINIMUM

H

30"

(76 cm)

Fig. A-1

F03138Q01CP
iPress0109-2
Printed in China

IP2386_38Q01CP_Eng_04_080105.indd   1

IP2386_38Q01CP_Eng_04_080105.indd   1

2009-1-6   Michael 9:16:48

2009-1-6   Michael 9:16:48

Summary of Contents for Over The Range Microwave Oven















Reviews: