Others
-119-
ª
To Display Date/Time
Indication
To display Date/Time Indication, set the
appropriate Date/Time in [DATE/TIME]
on the [DISPLAY SETUP] Sub-Menu.
(
-78-
)
You can also press the [DATE/TIME]
Button of the Remote Controller
repeatedly to display or change the
Date/Time Indication.
ª
To Change the Display Mode
By changing [DISPLAY] on the
[DISPLAY SETUP] Sub-Menu, you can
change the Display Mode to All Function
Display [ALL], Partial Display [PARTIAL]
and Minimum Display [OFF]. (
-78-
)
Owner ID
You can register your name and address
in your Movie Camera to identify the
owner.
1
Set [CAMERA FUNCTIONS] >>
[OTHER FUNCTIONS1] >>
[OWNER ID SET] >> [YES].
≥
The [OWNER ID] Menu appears.
2
Turn the [PUSH] Dial
(38)
to select
[PIN NUMBER] and press the
[PUSH] Dial
(38)
to input desired
numbers.
3
Turn the [PUSH] Dial
(38)
to select
numbers and press the [PUSH] Dial
(38)
to enter them.
≥
Be sure to input 4 digits. Otherwise
the Pin Number will not be
registered.
4
Press the [
∫
] Button.
5
Repeat Steps 2–4 to input desired
characters for [NAME] and
[POSTCODE].
≥
You can input up to 12 characters in
[NAME], and up to 11 characters in
[POSTCODE].
6
Press the [
∫
] Button to finish the
setup.
To Verify Owner ID
Keep pressing the [
;
] Button for
approximately 5 seconds.
To Correct the Contents
If Owner ID has already been set,
carrying out Step 1 will display [INPUT
PIN NUMBER] on the screen. Input the
Pin Number you have already selected.
If the number is not correct, the screen
will not change. If the number is correct,
the contents of the setup will be
displayed. (By repeating Steps 2 to 4,
you can change the contents.)
Initializing the Modes
You can change the Menu settings back
to the shipping condition.
1
Set [CAMERA FUNCTIONS] >>
[OTHER FUNCTIONS2] >>
[INITIAL SET] >> [YES].
≥
The initializing takes for a while.
≥
After the initializing is completed, the
[COMPLETED] Indication appears
with beeps.
≥
Initializing will not erase the Owner ID
setting and the clock setting (
-80-
) that
has been adjusted.
Warning/Alarm Indications
If any one of the following indications
lights up or flashes, please check the
condition of the Movie Camera.
3
: Condensation has occurred.
-130-
Y
: The accidental erasure prevention
slider on the inserted Cassette is
open (that is, set to [SAVE]).
You are about to do audio dubbing
on the unrecorded (blank) portion
of the tape.
No Cassette is inserted.
-74-
6
: The Battery is low. Recharge it.
-72-
0
: The built-in battery is low.
-80-
:
:
The video heads are dirty.
-130-
2
END:
The tape came to end during
recording.
REMOTE:
Wrong Remote Controller Mode
has been selected.
-71-
UNPLAYABLE TAPE
(OTHER FORMAT):
You are attempting to play back a
tape section that has been
recorded with a different TV
system.
UNABLE TO A. DUB
(LP RECORDED):
Because the original recording was
done in LP Mode, audio dubbing
cannot be performed.
INCOMPATIBLE TAPE:
This Cassette is incompatible.
PLEASE RE-OPERATE
AFTER PUSHING
RESET BUTTON:
Mechanism Irregular is detected.
Press the [RESET] Button (
-69-
).
This may solve the problem.
ENGText.fm 119 ページ ２００３年２月１４日 金曜日 午後９時１５分
