Panasonic NR-B32FW3 Service Manual Download

Page: 46 / 52

5. Install Cover Harness PCT R

a. Fix the connector into storage part.
b. Install hooks of Cover Harness PCT R into Door A’ssy

PC.

6. Install Cover Cap Door PCT R and Cover Table R

a. Install Cover Table R in Hooks of Top Table.
b. Screw Cover Table R.

c. Put and install hooks of Cover Cap Door PCT R into

Door A’ssy PC.

d. Screw Cover Cap Door PCT R.

11.8.6. Final check

1. Is there a gap between the body and the Door A'ssy PC,

when the door is closed? (If there is a gap, it might
become cause of leakage of cooling air.)

• Check whether there is a gap to put a sheet of paper

between the body and gasket like the figure.

2. If Gasket Door does not slide smoothly, check whether it

is set to the right position.
If there is something wrong like above, apply the grease
of bundled parts inside of Gasket Door.

Summary of Contents for NR-B32FW3





















































Search results

Summary of Contents for NR-B32FW3

Reviews:

Related manuals for NR-B32FW3

Brands by name

Popular brands

Panasonic NR-B32FW3, Service Manual

Search results

Summary of Contents for NR-B32FW3

Reviews:

Related manuals for NR-B32FW3

Brands by name

Popular brands