Panasonic NR-B32FW3 Service Manual Download | Manualshive

Page: 31 / 52

background image

31

11 Disassembly and Assem-

bly Instructions

11.1. Disassembly of PC (Refrigera-

tor Compartment)

11.1.1. LED board (PCB) inside the room

1. Pry off the LED lamp cover in the direction of the arrow in

a little small (-) screwdriver.

NOTES

• Be careful not to make a scratch by screwdriver (-) on

the surface of PC room.

• Please put a tape on the part where a screwdriver (-)

touch, to prevent being damaged on the inner surface.

2. Take the LED board out from the hooks (two).

3. Pull the connector of LED board out while pressing the

connector like the figure, it's possible to remove.

NOTES

• Be careful not to break LED board when it is removed

and installed.

11.1.2. Duct PC and Ag Filter board

1. Pry off and remove the Cap PC Duct (

×

3) by (-) screw-

driver.

2. Remove the fixed screws (three) in a (+) screwdriver,

then remove the Duct PC.

«
...
29
30
31
32
33
...
»

Summary of Contents for NR-B32FW3





















































Reviews:

No comments

Related manuals for NR-B32FW3

Brand: Samsung Pages: 20

Brand: Samsung Pages: 36

Brand: Samsung Pages: 16

Brand: inventum Pages: 64

Brand: Sharper Image Pages: 7

Brand: GE Pages: 104

Shelleyspeed SPRD36P-50NE

Brand: Delfield Pages: 2

Brand: Sauber Pages: 20

Brand: Jenn-Air Pages: 26

Brand: Everglades Pages: 78

Brand: NEFF Pages: 105

Brand: Blomberg Pages: 25

Brand: Hoshizaki Pages: 30

Brand: NewAir Pages: 14

Brand: Hanseatic Pages: 90

Brand: SNAIGE Pages: 13

Brand: Indel B Pages: 22

Brand: Zanussi Electrolux Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands