Panasonic NEXTIVA KT-TGP 600 User Manual Download Page 41

Page: 41 / 50

41 | P a g e

Enabling DND using a Star Code

Pick up

the Panasonic KX-TPA60 handset from the charger.

Press the green

TALK/Speakerphone

Key.

NOTE:

To switch to speakerphone, press the green

TALK/Speakerphone

key again. The screen

updates to say

Speaker Phone

. If you are using a headset, you cannot switch to speakerphone

mode.

Enter

*78

on the keypad. The call is initiated, and you hear an automated prompt saying the Do

Not Disturb service has been activated successfully.

Wait for the automated prompt to finish, or press the red

POWER/CANCEL

key on the phone to

disconnect the call. The screen on the handset updates to say

DND

Factory Reset

Turn Embedded Web on (see ‘Enabling the Web Configuration Utility’ above).

On the Panasonic KX-TPA60 handset, press the

MENU

softkey (middle softkey).

Select

System Settings



Status



IPv4 Settings



IP Address

from the menu.

Record the IP address that appears on the screen.

Enter the IP Address into the

address bar

of a web browser on your computer

(Figure 7-1)

Figure 7-1: Navigate to the Phone’s IP Address

Summary of Contents for NEXTIVA KT-TGP 600

















































Search results

Summary of Contents for NEXTIVA KT-TGP 600

Reviews:

Brands by name

Popular brands

Panasonic NEXTIVA KT-TGP 600, User Manual

Search results

Summary of Contents for NEXTIVA KT-TGP 600

Reviews:

Brands by name

Popular brands