Panasonic NA-128VA2 Service Manual Download Page 6

Page: 6 / 49

2-6 Smart Beat Wash by variable rotation control

Previous washing method

New washing method (Variable rotation control)

The drum rotates at a constant speed. Therefore, due to different fabrics and weights of clothing
and insufficient penetration of water, dirt can not be beaten out by washing.

The laundry s movement inside the drum shall
be detected by 3D sensor, and the drum rotates
most suitable speed to realize proper beat washing.

Heavily clothes

Lightly clothes

If clothes shall not be

penetrated water enough

If clothes shall not be

penetrated water enough

45 r/min

Increased rotation
speed of the drum

Decreased rotation
speed of the drum

3D Sensor

How to check the 3D sensor

Operate "Test-No water"

C-process: Spin Operation

Operate approx. 2 minutes with no load

(it shall be rotated smoothly)

1)Press

/ temp. switch =X-axis

2)Press r/min (spin) switch =Y-axis
3)Time (Reserve) switch =z-axis

If indicate below 30 (Actual

moving 3mm)

If indicate more than 30

Incase there is no data and signal coming from the
3D sensor to the main PC Board within 30 seconds
H41 shall be appeared.

Replace the 3D sensor

-6-

NA-168VX2/168VG2/148VA2/128VA2/147VB2

Summary of Contents for NA-128VA2


















































Search results

Summary of Contents for NA-128VA2

Reviews:

Related manuals for NA-128VA2

Brands by name

Popular brands

Panasonic NA-128VA2, Service Manual

Search results

Summary of Contents for NA-128VA2

Reviews:

Related manuals for NA-128VA2

Brands by name

Popular brands