Panasonic NA-128VA2 Service Manual Download Page 30 | Manualshive

Page: 30 / 49

background image

Procedure

Figure

4.pull all pawls up to remove the detergent case A
from the body joint.

5.Remove the two screws mounting the feed valve
unit as shown in left figure.

6.Remove the three connectors from the feed valve
unit, and pull it out to remove by a screwdriver.

After remove the upper board,
1.Remove the detergent case B, and remove the
one screw mounting the panel face board.

2.Remove another screw mounting the panel face
board.

3.Press all pawls mounting the panel face board
and pull it out slightly to remove.

-30-

6

Replacement of

the PC Board for
operation

Description

NA-168VX2/168VG2/148VA2/128VA2/147VB2

«
...
28
29
30
31
32
...
»

Summary of Contents for NA-128VA2


















































Reviews:

No comments

Related manuals for NA-128VA2

Brand: Haier Pages: 38

Brand: Haier Pages: 8

Brand: Lavorwash Pages: 28

Brand: Generac Portable Products Pages: 52

Brand: Amica Pages: 2

Brand: TOPMAQ Pages: 30

Brand: BorMann Pages: 18

Brand: Galanz Pages: 14

Brand: EHRLE Pages: 70

Brand: Zanussi Electrolux Pages: 24

Brand: Hotpoint Pages: 24

Brand: Smeg Pages: 42

Brand: Troy-Bilt Pages: 60

Brand: Rangemaster Pages: 28

Brand: Hotpoint Pages: 28

Brand: Alliance Laundry Systems Pages: 19

Brand: Lavor Pages: 56

Brand: Kärcher Pages: 516

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands