manualshive.com logo in svg

Panasonic MN101L Series, User Manual

The Panasonic MN101L Series, an innovative electronic device, comes with a comprehensive User Manual that provides detailed instructions on setup and optimal usage. You can conveniently download the manual for free from manualshive.com, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

<About This Manual - 1>

A b o u t   T h i s   M a n u a l

„

Objective

The primary objective of this LSI manual is to describe the features of this product including an 
overview, CPU basic functions, interrupt, port, timer, serial interface, and other peripheral hardware 
functions.
Each section consists of brief functional information, block diagrams and the details of control registers 
including operation methods and setting examples.

„

Structure of This Manual

Each section of this manual consists of a title, summary, main text, hint, precautions and warnings, and 
references.
The layout and definition of each section are shown below.

This page serves as an example to the explanations above. It may be different on an actual page.

Precautions and
warnings

Please be sure to read 
the precautions to prevent
any loss of functionality or
damage to the chip.

Main text

Section title

Sub section title

Header

Chapter number and
Chapter title

footer

Hint

chapter 2
Basic CPU

I I - 4 8

Reset

2.8

Reset

2.8.1

Reset operation

the CPU contents are reset and registers are intialized when the NRST pin (P
27) is pulled to low.

 Initiating a Reset
There are two methods to initiate areset.
(1)   Drive the NRST pin low for at least four clock cycles.
       NTST pin should be holded "low" for more than 4 clock cycles (200 ns a
       t a 20 NHz)

Figure:2.8.1  MInimum Reset PUlse Width

(2)   Setting the P2OUT7 flag of the P2OUT register to "0" outputs low level at P
       27 (NRST) pin. And transfering to reset by program (software reset) can be 
       executed. If the internal LSI is reset and register is initiated, the P2OUT
       7 flag becomes "1" and reset is released.

     On this LSI, the starting mode is NORMAL mode that high oscillation i
      s the base clock.

      When the power voltage low circuit is connected to NTST pin, circuit t
      hat gives pulse for enough low level time at sudeen unconnected. And r
      set can be generated even if its pulse is low level as the oscillation
      clock is under 4 clocks,take notice of noise.

NRST pin

4 clock cycles

(200 ns at a 20 MHz)

Important information
from the text.

Page # and
section title.

Summary of Contents for MN101L Series




















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MN101L Series

Data Translation DT300 Series Getting Started Manual preview
DT300 Series
Brand: Data Translation Pages: 98
IBM AS/400 Hardware User Manual preview
AS/400
Brand: IBM Pages: 104
IBM System Storage TS3100 Setup, Operator, And Service Manual preview
System Storage TS3100
Brand: IBM Pages: 375
Quantum Scalar 50 Upgrade Instructions preview
Scalar 50
Brand: Quantum Pages: 20
TFortis Teleport-1 Configuration Manual preview
Teleport-1
Brand: TFortis Pages: 86
Telex Communications 2472AA Instruction Manual preview
2472AA
Brand: Telex Communications Pages: 28
Caton NVE 9100 User Manual preview
NVE 9100
Brand: Caton Pages: 18
HighPoint RocketCache 3240X8 User Manual preview
RocketCache 3240X8
Brand: HighPoint Pages: 17
Riverbed SteelCentral AppResponse 2180 Upgrade And Maintenance Manual preview
SteelCentral AppResponse 2180
Brand: Riverbed Pages: 82
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
Cypress PSoC 4 S Series Quick Start Manual preview
PSoC 4 S Series
Brand: Cypress Pages: 4
ATI Technologies RADEON 9800 PRO Getting Started Manual preview
RADEON 9800 PRO
Brand: ATI Technologies Pages: 20
PairGain T1L2N20A Manual preview
T1L2N20A
Brand: PairGain Pages: 80
ATTO Technology iPBridge 2500C Specifications preview
iPBridge 2500C
Brand: ATTO Technology Pages: 2
AMD Geode LX 800 User Manual preview
Geode LX 800
Brand: AMD Pages: 27
EXAGATE SYSGuard 6001 Quick Installation Manual preview
SYSGuard 6001
Brand: EXAGATE Pages: 7
Renesas Protection Board R0E330850ACBP0 User Manual preview
Protection Board R0E330850ACBP0
Brand: Renesas Pages: 8
Kontron PC/104-PCMCIA-1 User Manual preview
PC/104-PCMCIA-1
Brand: Kontron Pages: 20

Brands by name

Popular brands

Load more brands