Panasonic KX-UT670 Administrator'S Manual Download Page 241

Page: 241 / 250

•

5.2.1 Configuration File Specifications for Plain Text Provisioning (Page 135)

•

5.4.2 System Time Settings—TIME_ZONE_COUNTRY (Page 141)

•

10.1 Troubleshooting —SD Cards (Page 234)

12.1.2 Software File Version 01.070

New Contents

•

4.4.2.2 LLDP Settings

→

LLDP (Page 74)

→

LLDP-MED Interval timer (Page 74)

→

PC (VLAN ID) (Page 75)

→

PC (Priority) (Page 75)

Changed Contents

•

1.1.3 Basic Network Setup (Page 16)

•

2.4.4.2 XML Element/Attribute Configuration Parameter Table

→

X_P_IPTEL_LLDP (Page 41)

•

4.1 Web User Interface Setting List

→

LLDP (Page 74)

•

4.4.2 Ethernet Port Settings (Page 73)

•

5.1 Configuration File Parameter List

→

Network Settings (Page 129)

•

5.5.1 Ethernet Port Settings

→

LLDP_ENABLE (Page 151)

→

LLDP_INTERVAL (Page 152)

→

LLDP_VLAN_ID_PC (Page 152)

→

LLDP_VLAN_PRI_PC (Page 152)

Document Version 2012-07

Administrator Guide

241

Section 12 Appendix

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands