Panasonic KX-UT670 Administrator'S Manual Download Page 152

Page: 152 / 250

Web User Interface Reference

LLDP (Page 74)

LLDP_INTERVAL

Value Format

Integer

Description

Specifies the interval, in seconds, between sending each LLDP frame.

Value Range

1–3600

Default Value

Phone User Interface
Reference

Ethernet Settings (Page 17)

Web User Interface Reference

LLDP-MED Interval timer (Page 74)

LLDP_VLAN_ID_PC

Value Format

Integer

Description

Specifies the VLAN ID for the PC port when LLDP is on.

Value Range

0–4094

Default Value

Web User Interface Reference

PC (VLAN ID) (Page 75)

LLDP_VLAN_PRI_PC

Value Format

Integer

Description

Specifies the VLAN Priority for the PC port when LLDP is on.

Value Range

0–7

Default Value

Web User Interface Reference

PC (Priority) (Page 75)

VLAN_ENABLE

Value Format

Boolean

152

Administrator Guide

Document Version 2012-07

Section 5 Configuration File Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands