Panasonic KX-TS600EX Operating Instructions Manual Download Page 44

Page: 44 / 48

Problem

Cause and Remedy

The unit does not work.

• Check the settings (p. 6–14).
• Remove the batteries and reinstall them

to reset the unit.

• KX-TS600EXW or KX-TS600EXB is not

designed to be used with rotary (pulse
dialing) services.

The unit does not ring.

• The ringer selector is set to OFF. Set to

HIGH or LOW (p. 13).

The display is blank.

• Install new batteries (p. 43).

You cannot dial.

• Dial lock mode is set. To cancel the

mode, see page 39.

• The dialed number is restricted. To

cancel, see page 41.

The other party suddenly
cannot hear your voice
during a conversation.

•

[

]

may have been pressed during the

conversation. If “

” is displayed, press

[

]

(p. 36).

You cannot program items
such as the dialing mode.

• Programming is not possible when the

handset is off the cradle, the
Speakerphone/headset

[

]

indicator

lights, or when viewing the Caller List
and the Phonebook.

• Do not pause for over 60 seconds while

programming.

The unit does not display
the caller’s phone number.

• You need to subscribe to a Caller ID

service.

• Install or replace the batteries.
• Another telephone equipment may be

interfering with your phone. Disconnect
it and try again.

• Telephone line noise may be interfering

with the Caller ID information. Consult
your telephone company.

While programming or
searching, the unit starts to
ring and stops the program/
search.

• To answer the call, lift the handset or

press

[

]

. Start again from the

beginning after hanging up.

Troubleshooting

TS600EX.book Page 44 Wednesday, April 5, 2006 12:25 PM

Summary of Contents for KX-TS600EX

















































Search results

Summary of Contents for KX-TS600EX

Reviews:

Related manuals for KX-TS600EX

Brands by name

Popular brands

Panasonic KX-TS600EX, Operating Instructions Manual

Search results

Summary of Contents for KX-TS600EX

Reviews:

Related manuals for KX-TS600EX

Brands by name

Popular brands