Panasonic KX-TG7100FXS, Service Manual

Page: 21 / 82

21
KX-TG7100FXS/KX-TG7100FXT/KX-TG7102FXS/KX-TGA711FXS/KX-TGA711FXT
Frequently Used Items (Base Unit)
ex.)
Note:
(*1) Refer to Registering a Handset to the Base Unit (P.18)
(*2) When you enter the address or New Data, please refer to the table below.
(*3)
(*4)
(*5) The new data must be entered in all three addresses (01 F6, 03 8A, 03 8B) using the same value.
Ex.) If you want to change the bell length to “1E (3 sec)”.
01 F6 - 1E
03 8A - 1E
03 8B - 1E
Items (*3) Address Default Data New Data Remarks
C-ID (FSK) sensitivity 04 6F 00 01 (6dB up) 02 (12dB up) When hex changes from “00” to “01” or “02”,
gain increases by 6dB or 12dB.
C-ID (DTMF) sensitivity 04 7D 50 60 (6dB up) 70 (12dB up) When hex changes from “50” to “60” or “70”,
gain increases by 6dB or 12dB.
SMS (FSK) receiving sensitiv-
ity 04 6F 00 01 (6dB up) 02 (12dB up) When hex changes from “00” to “01” or “02”,
gain increases by 6dB or 12dB.
SMS (FSK) sending level 04 89/04 88 0x12/0x28 19/20 (6dB up) 32/40 (12dB
up)
When hex changes from “00 0B” to “00 16” or
“00 2C”, gain increases by 6dB or 12dB.
Frequency 00 01 75 - - Use these items in a READ-ONLY mode to
confirm the contents. Careless rewriting may
cause serious damage to the computer system.
ID 00 10~00 14 Given value - -
Bell length 01 F6
03 8A
03 8B 64 (10sec) (*4)
32 (5sec)
64 (10sec)
1E (3sec) (*5) 14 (2sec)
(*2)
This is time until bell stops ringing.
(Unit: 100ms)
PULSE Dial speed
(10PPS -> 20PPS) 03 5C
03 5E 2A (40msec)
(*4)
16 (20msec) - This is pulse make time. (Unit:1ms)
03 5D
03 5F
3A (60msec)
(*4)
1C (30msec) - This is pulse break time. (Unit:1ms)
01 E4 57 (870msec)
(*4)
2C (440msec) - This is inter-digit time in pulse mode.
(Unit:10ms)
Desired Number (hex) Input Keys Desired Number (hex) Input Keys
0 0 A [R] + 0
1 1 B [R] + 1
. . C [R] + 2
. . D [R] + 3
. . E [R] + 4
9 9 F [R] + 5
Items Description
C-ID (FSK) sensitivity FSKGain_shiftgain
C-ID (DTMF) sensitivity Foutgains:HPFilter Foutgains
SMS (FSK) receiving sensitivity FSKGain_shiftgain
SMS (FSK) sending level wFskAttn:Signal Output Attenuation (DSP parameter)
Frequency Setting value of FREQ_TRIM_REG
ID ID
Bell length Time until it stops bell.
PULSE Dial speed
(10PPS -> 20PPS) Pulse MakeTime and BreakTime.
bMakeTime:Pulse MakeTime Unit: 1ms
bBreakTime:Pulse Break Time Unit: 1ms
Inter-digit time in Pulse mode.
Unit:10ms
Bell length 64(hex) = 100(dec)
→
100
×
100msec = 10000msec (10sec)
PULSE Dial speed
(10PPS -> 20PPS) 2A(hex) = 42(dec)
→
(42-2)
×
1msec = 40msec
3A(hex) = 58(dec)
→
(58+2)
×
1msec = 60msec
57(hex) = 87(dec)
→
87
×
10msec = 870msec