Panasonic KX-TG6671C Operating Instructions Manual Download Page 21

Page: 21 / 52

Main menu: “

Ringer volume

”

Operation

Settings

Code

Adjusting the ringer volume. (Base unit)

Off–6 <6>

#160

Main menu:

“

Initial settings

”

Sub-menu 1

Sub-menu 2

Settings

Code

Contrast

(Display contrast)

–

Level 1–6 <3>

#145

–

Change language

(Display) (Base unit)

–

English

Français

#110

Main menu:

“

Customer support

”

Operation

Code

Displaying customer support Web address.

#680

–

*1 Ringer volume cannot be turned off for intercom calls and paging.
*2 The base unit can display the Internet address where you can download the operating instructions or

get further information for this product, using your computer.

Handset

Main menu:

“

Caller list

”

Operation

Code

Viewing the caller list.

#213

Main menu:

“

Answering device

”

Sub-menu 1

Sub-menu 2

Settings

Code

Play new msg.

(

msg.

: message)

–

#323

Play all msg.

–

#324

Erase all msg.

–

#325

Greeting

Record greeting

–

#302

Check greeting

–

#303

Pre-recorded

(Reset to pre-recorded
greeting)

–

#304

Settings

Ring count

2–7:

–

7 rings

4 rings

Toll saver

#211

Recording time

1 min

3 min

Greeting only

#305

Remote code

111

#306

Screen call

Off

#310

Answer on

–

#327

Programming

Summary of Contents for KX-TG6671C





















































Search results

Summary of Contents for KX-TG6671C

Reviews:

Related manuals for KX-TG6671C

Brands by name

Popular brands

Panasonic KX-TG6671C, Operating Instructions Manual

Search results

Summary of Contents for KX-TG6671C

Reviews:

Related manuals for KX-TG6671C

Brands by name

Popular brands