Panasonic KX-TCD735ALM Operating Instructions Manual Download Page 74

Page: 74 / 114

Call Restriction

with the Handset

To cancel the call restricted
handset(s)

Follow steps 1 to 3 on Setting the Call
Restriction, then enter the handset
number(s) you desire to cancel.

•

The cancelled handset number(s) stop(s)
flashing.

Press

repeatedly until “

Setting

Base

” is displayed.

•

To return to the standby mode, press

•

You can exit the programming mode any time
by pressing

To cancel the call restriction
number(s)

Follow steps 1 to 3 on Setting the Call
Restriction.

Press .

Press

repeatedly until the call

restriction number you desire to cancel

is displayed, then erase the number by

pressing .

•

The call restriction number is cleared.

Press

repeatedly until “

Setting

Base

” is displayed.

•

To return to the standby mode, press

•

You can exit the programming mode any time
by pressing

KX-TCD735ALM(E)-3(50~75) 2002.06.21 5:24 PM Page 74

Summary of Contents for KX-TCD735ALM



















































































































Search results

Summary of Contents for KX-TCD735ALM

Reviews:

Related manuals for KX-TCD735ALM

Brands by name

Popular brands

Panasonic KX-TCD735ALM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD735ALM

Reviews:

Related manuals for KX-TCD735ALM

Brands by name

Popular brands