Panasonic KX-TCD735ALM Operating Instructions Manual Download Page 45

Page: 45 / 114

Chapter 2

Cordless T

elephone

with the Handset

Phonebook Copy

You can copy the item in the handset phonebook between the handsets registered in the same base
unit. The phonebook copy must be operated in intercom mode (p. 98).
Ex. Handset 2 is copying the handset phonebook to Handset 1 during an intercom call.

Make sure that the power is ON (p. 15), and the unit is in the standby mode.

Handset 2 (Sender):

Press .

Press

until the arrow points

to “

Send Phonebook

”, then press

•

The phonebook is displayed.

Press

until the name you

desire to copy is displayed, then press

Press

until the arrow points

to “

Copy Entry

”, then press

•

“

Copy Proceeding

” is on the display

with beep sound and the selected
information is copied.

•

After copying is completed, a beep sounds
and “

Copy Complete

” is displayed.

•

After a few seconds, the display will return
to the intercom call.

•

If “

Memory Full

” is displayed, the receiver

handset memory is full.

•

If “

Copy Failure

” is displayed, the receiver

and/or sender did not prepare for copying
within 60 seconds.

Handset 1 (Receiver):

During an intercom call, press

Press

until the arrow points

to “

Recv Phonebook

”, then press

•

“

Copy Proceeding

” is on the display.

•

If “

Memory Full

” is displayed, the receiver

handset memory is full.

To copy a selected item in the handset phonebook

KX-TCD735ALM(E)-2(32~49) 2002.06.21 5:02 PM Page 45

Summary of Contents for KX-TCD735ALM



















































































































Search results

Summary of Contents for KX-TCD735ALM

Reviews:

Related manuals for KX-TCD735ALM

Brands by name

Popular brands

Panasonic KX-TCD735ALM, Operating Instructions Manual

Search results

Summary of Contents for KX-TCD735ALM

Reviews:

Related manuals for KX-TCD735ALM

Brands by name

Popular brands