Panasonic KX-HTS824 Feature Manual Download Page 42

Page: 42 / 80

Conditions

Note

It is possible to redial a maximum of 32 digit dial numbers.

Numbers dialed after starting the conversation are not stored in the
redial memory.

When executing Walking COS, the extension being operated will
store the redial memory.

3.2.8 Video Communication for Intercom Call

Description

It is possible to make a video call between 2 SIP extensions.
Devices that support video communication are listed below:

•

KX-NTV series

•

General SIP phones

Operation

SIP extensions can make a video call only when a call is started with an extension using the following
features:

•

3.2.6 Intercom Calling

•

3.2.7 Redial

•

3.1.9 Call Forwarding (FWD)

•

3.1.12 Extension Group Call

•

3.3.1 System Speed Dial

•

3.6.1 Call Waiting

Conditions

Note

SIP extension users cannot make a video call if they make a call
using the following features (audio call only):

•

3.1.4 DISA (Direct Inward System Access)

•

3.1.8 Call Pickup

•

3.9 Conference Features

•

3.10 Paging Features

•

5 Voice Mail Features

SIP extensions cannot use the following features during a video call:

•

Video to Audio/Audio to Video switching (Refer to the manual for
your telephone.)

•

3.7 Holding Features

•

3.8 Transferring Features

3.2.8 Video Communication for Intercom Call

Feature Manual

Summary of Contents for KX-HTS824

















































































Search results

Summary of Contents for KX-HTS824

Reviews:

Related manuals for KX-HTS824

Brands by name

Popular brands

Panasonic KX-HTS824, Feature Manual

Search results

Summary of Contents for KX-HTS824

Reviews:

Related manuals for KX-HTS824

Brands by name

Popular brands