Panasonic KX-HDV230 Administrator'S Manual Download Page 178

Page: 178 / 342

DTMF Settings

Parameter Name

Ref.

DTMF_METHOD_n

OUTBANDDTMF_VOL

INBANDDTMF_VOL

DTMF_SIGNAL_LEN

DTMF_INTDIGIT_TIM

Page 270

RTP/RTCP/RTCP-XR Settings

Parameter Name

Ref.

DSCP_RTP_n

DSCP_RTCP_n

MAX_DELAY_n

MIN_DELAY_n

NOM_DELAY_n

RTP_PORT_MAX

RTP_PTIME

RTP_TARGET_CHECK

RTCP_ENABLE_n

RTCP_INTVL_n

RTCP_SEND_BY_SDP_n

Page 273

RTP_CLOSE_ENABLE_n

Page 274

RTCPXR_ENABLE_n

Page 274

SRTP Settings

Parameter Name

Ref.

SRTP_CONNECT_MODE_n

Page 274

SRTP_MIX_CONFERENCE_ENABLE_n

Page 275

SRTP_MIX_TRANSFER_ENABLE_n

Page 275

SRTP_HELD_CALL_RTP_ENABLE

Page 275

178

Administrator Guide

Document Version 2015-07

5.1 Configuration File Parameter List

Summary of Contents for KX-HDV230























































































































































































































































































































































Search results

Summary of Contents for KX-HDV230

Reviews:

Panasonic KX-HDV230, Administrator'S Manual, Page: 178 / 342

Search results

Summary of Contents for KX-HDV230

Reviews: