Panasonic KX-FM330GR Service Manual Download Page 67

Page: 67 / 264

2 TROUBLESHOOTING GUIDE

2.1. TROUBLESHOOTING SUMMARY

2.1.1. TROUBLESHOOTING

After confirming the problem by asking the user, troubleshoot according to the instructions and observe the following precautions.

2.1.2. PRECAUTIONS

1. If there is a problem with the print quality or the paper feed, first check if the installation space and the print paper meets the

specifications, the paper selection lever/paper thickness lever is set correctly, and the paper is set correctly without any slack.

2. Before troubleshooting, first check that the connectors and cables are connected correctly (not loose). If the problem occurs

randomly, check it very carefully.

3. When connecting the AC power cord with the unit and checking the operation, exercise utmost care when handling electric

parts in order to avoid electric shocks and short-circuits.

4. After troubleshooting, double check that you have not forgotten any connectors, left any loose screws, etc.

5. Always test to verify that the unit is working normally.

2.1.3. WHEN YOU DON´T KNOW HOW TO OPERATE THE UNIT, USE THE HELP

FUNCTION

Note:

Words in brackets ( ) are German. A translated version for each market is available with this model series.

KX-FP320G / KX-FM330G

Summary of Contents for KX-FM330GR









































































































































































































































































Search results

Summary of Contents for KX-FM330GR

Reviews:

Related manuals for KX-FM330GR

Brands by name

Popular brands

Panasonic KX-FM330GR, Service Manual

Search results

Summary of Contents for KX-FM330GR

Reviews:

Related manuals for KX-FM330GR

Brands by name

Popular brands