Panasonic KV-S3085 Operating Instructions Manual Download | Manualshive

Page: 5 / 62

background image

Notice

5

(For United Kingdom only)
For your safety please read the following text carefully.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
A 5 amp. fuse is fitted in this plug. Should the fuse need to be replaced, please ensure that the replacement fuse has a rating of 5
amps. and that it is approved by ASTA or BSI to BS1362. Check for the ASTA mark

or the BSI mark

on the body of the

fuse. If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced. If you lose the fuse
cover the plug must not be used until a replacement cover is obtained. A replacement fuse cover can be purchased from your
local Panasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in your home then the fuse should be removed and the plug cut off and
disposed of safely.
There is danger of severe electrical shock if the cut off plug is inserted into any 13 amp. socket.
If a new plug is to be fitted please observe the wiring code as shown below. If in any doubt please consult a qualified electrician.

WARNING:

This appliance must be earthed.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code.

Green-and-Yellow

: Earth

Blue

: Neutral

Brown

: Live

As the colours of the wire in the mains lead of this appliance may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows.

The wire which is coloured Green-and-Yellow must be connected to the terminal in the plug which is marked with the letter E or by
the Earth symbol

or coloured Green-and-Yellow.

The wire which is coloured Blue must be connected to the terminal in the plug which is marked with the letter N or coloured Black.
The wire which is coloured Brown must be connected to the terminal in the plug which is marked with the letter L or coloured Red.

ASA

How to replace the fuse:

Open the fuse compartment with a screwdriver and replace
the fuse.

«
...
3
4
5
6
7
...
»

Summary of Contents for KV-S3085































































Reviews:

No comments

Related manuals for KV-S3085

Brand: Keithley Pages: 80

Brand: Xerox Pages: 62

SmartSource Elite Series

Brand: Digital Check Pages: 32

MorphoSmart MSO300

Brand: Safran Pages: 44

UBC 245XLT Trunk Tracker II

Brand: Uniden Pages: 90

A4 Multi-Purpose

Brand: Digi-Frame Pages: 26

Brand: GRAPHTEC Pages: 164

Brand: AGFA Pages: 81

Brand: Element Pages: 53

Brand: R&S Pages: 70

Brand: QPIX Pages: 2

Brand: Xerox Pages: 41

Brand: JCD Pages: 39

Brand: NCR Pages: 62

Brand: QVI Pages: 100

Brand: Unitech Pages: 34

Brand: Panasonic Pages: 24

Microfilm Scanner 350

Brand: Canon Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands