background image

8

Technical data common to all models

6.  Technical data common to all models

6.1 

Hardware specifications

Touch screen technology

Resistive

Real-time clock back-up 

Supercapacitor

Fuse

Automatic

Serial port 

RS232, RS485, RS422 software configurable

Recipe memory

Flash 

Real-time clock

Clock/calendar with supercapacitor back-up

Accuracy real-time clock 

(at 25°C)

<100ppm

6.2  Environmental conditions

Operating temperature  

(surrounding air temperature)

0 to +50°C

EN 60068-2-14

Storage temperature 

-20 to +70°C

EN 60068-2-14

Operating and storage humidity 

5–85% RH not-condensing

EN 60068-2-30

Vibrations 

5–9Hz, 7mm 

p-p

9–150Hz, 1g

EN 60068-2-6

Shock

±50g, 11ms, 3 pulses per axis

EN 60068-2-27 

Degree of protection

IP66 front panel (see note)

EN 60529

Pollution degree environment

2

The front face of the unit, installed in a solid panel, has been tested using conditions equivalent to the stan

-

dards shown in the “Environmental conditions”. Even though the level of resistance unit is equivalent to these 

standards, oils that should have no effect on the HMe can possibly harm the unit. This can occur in areas 

where either vaporized oils are present, or where low viscosity cutting oil are allowed to adhere to the unit for 

long periods of time. If the front face protection sheet on the HMe becomes peeled off, these conditions can 

lead to the ingress of oil into the unit and separate protection measures are suggested.

 

If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the 

panel, the original degree of the protection cannot be guaranteed.

Summary of Contents for HMe Series



























Reviews: