Communications Protocol
Model: GP-HB310
[3] Command List for
HB310
Message
All Initial
A0 01 0A CS FF
Initialization of Unadjusted EEPROM Values (Set to Factory Defaults)
All Menu Initial
A0 01 0B CS FF
Initialization of All Menu Settings
Lens Initial
A0 01 0C CS FF
Detection of initial lens position
Reset
A0 01 0D CS FF
Restarting camera (Saves the setting value)
Custom preset
A0 01 14 0p CS FF
Custom Preset Function. p: (0:C.Reset, 1:C.Memory, 2:C.Recall)
* Refer to the function detail [14] Customer Preset Function.
PWR on lens position set
A0 01 15 0p CS FF
Lens position return function at power on. p:(0:OFF [Initial value], 1:ON)
VideoOut Mode
A0 01 20 0p 0q CS FF
VideoOut Mode Setting
p:
(
0:LVDS 1:Component 2:Composite
)
[Initial value: 0]
q:
(
Digital (LVDS): 0:1080p(30/25Hz) 1:1200p(30/25Hz) 2:1080i(60/50Hz) 3:720p(60/50Hz)
Component 0:1080p(60/50Hz) 1:1080i(60/50Hz) 2:720p(60/50Hz) 3:480p(60/50Hz)normal
4:480p(60/50Hz)crop 5:480p(60/50Hz)squeeze 6:1080p(30/25Hz)
Composite
0:normal 1:crop 2:squeeze
[Initial value: 2]
)
Ntsc/Pal
A0 01 21 0p CS FF
Set NTSC/PAL . p: (0: NTSC, 1: PAL)
System
Aspect Ratio
A0 01 40 0p CS FF
Set Aspect Ratio. p
:
(
0: 16:9
, 1:
4:3
)
[Initial value: 0]
Tele
A0 02 05 CS FF
Wide
A0 02 06 CS FF
Tele/Wide Stop
A0 02 07 CS FF
Tele/Wide Speed
A0 02 08 0p CS FF
p: Speed 1-5 during Tele and Wide commands (1: Slow-5: Fast [Initial value: 3])
Direct
A0 02 09 0p 0q 0r CS FF
pqr: Direct Position
・
0: Wide, 1600: 10x (optical), 1750: 160x (digital)
Digital Zoom Tele Limiter command needs to be sent before moving to digital zoom field.
Zoom Direct with Focus
A0 02 0A 0p 0q 0r 0s 0t
0u
CS FF
pqr:Zoom Direct Position stu:Focus Direct Position
For carrying set the focus to the specified position.
Digital Zoom Tele Limiter
A0 02 18 0p CS FF
p: Maximum digital zoom magnification (0: x1 [Initial value], 1: x2, 2: x4, 3: x8, 4: x16)
Optical Zoom Wide/Tele
Limitter
A0 02 19 xx yy CS FF
Wide/Tele Optical ZOOM Limiter
xx: 0, 1-9 (0 is no limit and 1-9 is the Wide optical ZOOM limit)
yy: 0, 2-10 (0 is no limit and 2-10 is the Tele optical ZOOM limit)
Note: Ensure that xx < yy
V-Reso.UP OFF/ON
A0 02 1F 0p CS FF
p: Increased vertical sensitivity settings during digital zoom (0: OFF [Initial value, 1: ON) (Note 3)
Zoom Preset ON
A0 02 28 CS FF
Moves the zoom position to the optical TELE edge
Zoom
Zoom Preset OFF
A0 02 29 CS FF
Returns the zoom position to the position before the “Zoom Preset ON” operation
Auto Focus ON
A0 03 00 CS FF
[Initial value: Auto Focus ON]
Manual Focus ON
A0 03 01 CS FF
One Push Trigger
A0 03 03 CS FF
Operates the auto focus operation once
Far
A0 03 05 CS FF
Near
A0 03 06 CS FF
Far/Near Stop
A0 03 07 CS FF
Far/Near Speed
A0 03 08 0p CS FF
p: Speed 1-4 during Far and Near commands (1: Slow-4: Fast [Initial value: 2])
Direct
A0 03 09 0p 0q 0r CS FF
pqr: Direct Position
0(Far)
-‐‑‒
2160(Near)
Near Limiter
A0 03 0E 0p CS FF
p: Subject distance limit during auto focus and manual focus
(0: 10 cm, 1: 30cm, 2: 50 cm, 3: 1 m [Initial value], 4: 3 m , 5: 5 m)
Auto Focus Sensitivity
A0 03 10 0p CS FF
p: Auto focus restart sensitivity settings (0: MIDDLE [Initial value], 1:HIGH, 2: LOW)
Focus Area
A0 03 13 0p CS FF
Settings Determining Auto Focus Areas 1-3
1: Entire screen-3: Only center of the screen [Initial value: 2]
Cover Offset OFF/ON
A0 03 15 0p CS FF
p: Offset OFF/ON (0: OFF/1: ON [Initial value]) when using the cover
Cover Offset Level
A0 03 16 0p 0q CS FF
pq: Offset Level Setting 0 – 100 [Initial value: 5] when using the cover
Auto Focus Mode during
pan/tilt
A0 03 1F 0p CS FF
p: Auto Focus Mode Setting during Pan/Tilt (0: AF[Initial value], / 1: Fixed)
AF Return
A0 03 22 0p CS FF
Auto Focus Return time p: ( 0: 20sec 1: 30sec [Initial value] 2: 40sec 3: 50sec 4: 1min 5: 2min
6: 3min 7: 4min 8: 5min 9: Auto )
Focus
AF by Face Detect
A0 03 30 0p CS FF
Auto Focus by Face Detect p (0:OFF[Initial value], 1:ON)
ATW
A0 04 00 CS FF
Auto White Balance Mode (Same as "0" in WB Mode)
MWB
A0 04 01 CS FF
Manual White Balance Mode (Same as "2" in WB Mode)
One Push Trigger(AWC Set)
A0 04 03 CS FF
Executes OnePush in AWC Mode
(Note 4)
AWC Reset
A0 04 04 CS FF
Returns to the original mode only after executing the OnePush Trigger command
MWB MODE in AWC
A0 04 05 CS FF
Retain the result of AWC(one-push WB) and go into the MWB mode
ATW Smart OFF/ON
A0 04 06 0p CS FF
Smart ATW (high color saturation compensation) ON/OFF (OFF: 0 , ON: 1[Initial value])
*This mode is valid when WB mode is set to ATW.
WB Mode
A0 04 07 0p CS FF
p: White Balance Mode 0-5 (0: Auto White Balance, 1: AWC Mode (One-Push N/A),
2: Manual White Balance 3: 3200K Fixed Mode, 4: 5600K Fixed Mode, 5: FLUO Mode (4200K Fixed))
MWB Red +
A0 04 0B CS FF
MWB Red -
A0 04 0C CS FF
MWB Red Preset
A0 04 0F CS FF
Returns MWB red component settings to factory defaults
( Initial value: 127[Firm Ver.1.01-00] :142[Firm Ver.1.01-01 - ] )
MWB Red Direct
A0 04 13 0p 0q CS FF
pq: Direct MWB red components 0-255
MWB Blue +
A0 04 15 CS FF
MWB Blue -
A0 04 16 CS FF
MWB Blue Preset
A0 04 19 CS FF
Returns MWB blue component settings to factory defaults
( Initial value: 127[Firm Ver.1.01-00] :110[Firm Ver.1.01-01 - ] )
MWB Blue Direct
A0 04 1D 0p 0q CS FF
pq: Direct MWB blue components 0-255
ATW Masking OFF
A0 04 28 CS FF
ATW Masking ON
A0 04 29 CS FF
Mask settings ON/OFF during ATW
ATW Mask Area Clr
A0 04 2D CS FF
Initialization of mask settings during ATW
White
Balance
ATW Mask Area Set
A0 04 31 0p 0q 0r 0s 0t
0u
CS FF
Mask area settings during ATW
(Note 1)
CS: Checksum
FF: Terminator
−
9
−
Summary of Contents for GP-MH310 series
Page 36: ... 34 ...
Page 38: ...Change history 2011 1 18 the issue of ver 1 10 36 ...
Page 43: ......