Panasonic DP-MB350, Operating Instructions Manual

Page: 74 / 120

9. Programmable Features
74
Approving users for the LAN
connection
{#}{
5
}{
3
}{
2
}
{
0
}
“
Disabled
” (default): Deactivates this feature.
{
1
}
“
Enabled
”: The unit will deny/approve access from the pre-programmed
IP patterns. You can program whether to deny or approve IP addresses. Up to
4 patterns each for IPv4 and IPv6 can be programmed through the web browser
interface.
1. Start Multi-Function Station.
2.
[
Utilities
]
i
[
Configuration Web Page
]
i
[
Network Configuration
]
3. Type “root” as the user name, then enter the password (feature #155 on
page 58).
i
[
OK
]
4. Select the
[
LAN Feature
]
tab.
5. Click
[
Edit
]
next to
[
Approved Users
]
.
6. Click
[
Edit
]
next to
[
Filter (IPv4)
]
/
[
Filter (IPv6)
]
.
7. Change the mode and edit IP filtering information. i
[
Submit
]
8. Close the web browser.
Setting the IP address
automatically for the LAN
connection
{#}{
5
}{
3
}{
3
}
This feature will be displayed only when feature #500 is activated.
{
0
}
“
Disabled
” (default): Deactivates this feature.
{
1
}
“
Enabled
”: IP address will be allocated automatically without using a
DHCP (Dynamic Host Configuration Protocol) server.
Setting HTTPD for the LAN
connection
{#}{
5
}{
3
}{
4
}
{
0
}
“
Disabled
”: Denies access to the web browser.
{
1
}
“
Enabled
” (default): Allows access to the web browser.
IPv6 protocol
{#}{
5
}{
3
}{
5
}
{
0
}
“
Disabled
” (default): Deactivates this feature.
{
1
}
“
Enabled
”: IPv6 protocol can be used. After installing the printer driver, be
sure to change the port to IPv6 protocol. You can check the IPv6 protocol
address by printing the “
Setup List
” (page 103).
Note:
L
To activate this feature, you need to turn the power switch of the unit OFF,
then ON.
Setting the paper input tray to
use for the scan to email print
feature
{#}{
5
}{
6
}{
5
}
This feature will be displayed only when the lower input tray is installed (page
79).
{
1
}
“
#1
” (default): Standard input tray
{
2
}
“
#2
”: Lower input tray
{
3
}
“
#1+#2
”
Note:
L
To select “
#2
”, select “
Plain Paper
” or “
Thin Paper
” for the recording
paper type setting (feature #383 on page 60).
L
To select “
#1+#2
”,
– select the same paper size for the standard input tray (feature #380 on
page 59) and lower input tray (feature #382 on page 59). If either is
changed, “
#1
” will be selected automatically.
– select “
Plain Paper
” or “
Thin Paper
” for the recording paper type
setting (feature #383 on page 60).
Erasing all email addresses
stored in the unit
{#}{
5
}{
7
}{
8
}
{
0
}
“
No
” (default)
{
1
}
“
Yes
”
L
Disconnect the telephone line cord, USB cable and LAN cable before
activating this feature.
To erase all email addresses:
1.
{
Menu
}
i
{#}{
5
}{
7
}{
8
}
2. Press
{
1
}
to select “
Yes
”.
i
{
Set
}
3. Press
{
1
}
to select “
Yes
”.
i
{
Set
}
i
{
Menu
}
Feature/Code Selection