76
RQT9058
Cannot operate the TV or Set Top
Box with the unit’s remote control.
Make necessary settings for the Set Top Box Control.
52
Change the manufacturer code on the remote control.
61
Select TV or Set Top Box mode on the remote control.
61
Cannot operate the DVD.
Press [DRIVE SELECT] to select the DVD dri
v
e when operating DVDs or
CDs.
–
Make sure the TV is on the correct channel or input mode.
14
Cannot operate the VHS.
Press [DRIVE SELECT] to select the VHS dri
v
e when operating VHS
cassettes.
–
Make sure the TV is on the correct channel or input mode.
15
The remote control doesn’t work.
The remote control code is wrong. Change to the correct code.
53
The batteries are depleted. Replace them with new ones.
5
Point the remote control at the remote control sensor on the main unit.
5
Remo
v
e obstacles between the remote control and main unit.
−
Remo
v
e dust from the transmission window and the unit’s sensor.
−
Colored glass may obstruct the signal reception/transmission.
−
Don’t place the signal sensor in direct sunlight or in areas that may be
subject to sun exposure.
−
It may be necessary to set the code on the remote control again after
changing the batteries.
53
It may be necessary to set the manufacturer code again after changing the
batteries.
61
The unit is on but cannot be
operated.
Some operations are prohibited by the disc.
−
The unit is warm (“U59” appears on the unit’s display).
W
ait until “U59”
disappears.
−
One of the unit’s safety de
v
ices may ha
v
e been acti
v
ated.
Reset the unit as follows:
Press [
/I PO
W
ER] on the main unit to switch to off.
If the unit doesn’t switch to off, reset the unit (
74, “To restore the unit if it
freezes”).
−
“U88” is displayed and the disc
cannot be ejected.
The unit is carrying out the reco
v
ery process. Do the following to eject the
disc:
(1) Press [
/I PO
W
ER] on the main unit to switch to off.
If the unit doesn’t switch to off, reset the unit (
74, “To restore the unit if
it freezes”).
(2)
W
hile the unit is off, press and hold [
] and [INPUT SELECT] on the
main unit at the same time for about 5 seconds. (Ejection may take extra
time depending on discs.) The disc may be defecti
v
e. Try another disc.
−
Cannot eject a disc.
The unit is recording.
−
The unit may ha
v
e a problem. Eject the disc as in (2) abo
v
e.
−
Startup is slow.
Startup takes time in the following situations:
–
A disc other than a DVD-RAM is inserted.
–
The clock is not set.
–
Immediately after a power failure or the AC power supply cord is
connected.
–
W
hen the unit is connected with an HDMI cable.
−
Cannot set “24p Output for DVD-
Video”.
Only when the unit is connected to the HDMI terminal of a TV supporting
24p, you can set “24p Output for DVD-Video”. In some cases where the unit
is connected to a TV
v
ia an amplifier/recei
v
er through the HDMI terminals,
you may not be able to set it. In this case, connect the unit to a TV through
the HDMI terminal and connect it to the amplifier/recei
v
er through any
terminal other than HDMI.
59
General Issues
Operation
Page
Troubleshooting Guide
DMR-EA38VP.indb 76
DMR-EA38VP.indb 76
2007/12/28 9:27:09
2007/12/28 9:27:09
Downloaded from
www.Manualslib.com
manuals search engine
Downloaded From DvDPlayer-Manual.com Panasonic Manuals
