79
RQT9056
Error Messages
On the Unit’s Display
Page
H , F
(“ ” stands for a ser
v
ice number.)
An error has occurred. The number following “H” or “F” depends on the
status of the unit. Check the items below and in the Troubleshooting Guide.
If the ser
v
ice number still does not disappear after the check, reset the unit
(
81, “To restore the unit if it freezes”).
−
If the ser
v
ice numbers fail to clear, note the ser
v
ice numbers and contact a
q
ualified ser
v
ice person.
−
RC (“ ” stands for a number.)
The remote control and the main unit are using different codes. Change the
code on the remote control.
57
HARD ERR
(“HArd” and “Err” are alternately
displayed.)
If there is no change after turning the unit on and off, consult the dealer
where the unit was purchased.
−
NO READ
(“NO” and “REAd” are alternately
displayed.)
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
75
The disc may be incompatible or of poor
q
uality.
74, 75,
76
You ha
v
e used a lens cleaner and it has finished operation. Press
[
OPEN/CLOSE] on the main unit to eject the disc.
15
Displayed when the unit is started. This is not a malfunction.
−
The unit is carrying out its reco
v
ery process. You cannot operate the unit
while “ ” is displayed.
−
FULL
There are already 16 scheduled recording programs. Delete unnecessary
scheduled recording programs.
27
UNSUPPORT
(“UNSUP” and “POrt” are alternately
displayed.)
You ha
v
e inserted a disc the unit cannot play or record on.
You tried to operate with a non-compatible USB memory.
74, 75
73
UNFORMAT
(“UNFOr” and “MAt” are alternately
displayed.)
You ha
v
e inserted a new DVD-R
W
/+R
W
or a DVD-RAM/DVD-R
W
(DVD-Video format) recorded on other e
q
uipment.
You can format the disc when the format confirmation screen is displayed.
25, 53
“
” is displayed on the unit’s
display.
This unit is confirming that it is connected with e
q
uipment compatible with
HDAVI Control.
−
F74
The HDMI connection could not be authenticated due to a transfer
malfunction. Consult the dealer where the unit was purchased.
−
F75
The HDMI connection could not be authenticated due to an internal data
malfunction. Consult the dealer where the unit was purchased.
−
U59
The unit is
v
ery warm.
The unit switches to standby for safety reasons.
W
ait for about 30 minutes
until the message disappears.
Reinstall the unit in an area with ade
q
uate
v
entilation. Do not block the
cooling fan on the rear of the unit.
−
U61
There was a power failure or the AC power supply cord was disconnected
while the unit was on. The unit is carrying out its reco
v
ery process. This
process restores the unit to normal operation. The unit is not broken.
W
ait
until the message disappears.
−
U72
U73
The HDMI connection acts unusually.
–
The connected e
q
uipment is not HDMI compatible.
–
Please use HIGH SPEED HDMI cables that ha
v
e the HDMI logo (as shown
on the co
v
er).
–
The HDMI cable is damaged.
−
U76
HDMI cannot be output because you are connected to a model that does
not support copyright protection.
−
U88
There was something unusual detected with the disc while recording,
playing or copying; there was a power failure or the AC power supply cord
was disconnected while the unit was on. The unit is carrying out its reco
v
ery
process. This process restores the unit to normal operation. The unit is not
broken.
W
ait until the message disappears.
83
U99
The unit fails to operate properly. Press [
/I PO
W
ER] on the main unit to switch the
unit to standby. Press [
/I PO
W
ER] on the main unit again to turn the unit on.
−
Continued on next page.
Ref
erence
DMR-EZ48VP.indb 79
DMR-EZ48VP.indb 79
2007/12/13 20:44:26
2007/12/13 20:44:26
