6
VQT3C69
STEP
1
Insert the CAM (Conditional Access Module) and Smart Card
You need a Conditional Access Module together with a valid Smart Card and a subscription with the corresponding CATV provider if you want to
watch/record encrypted digital CATV broadcasts.
1
Insert the certified Smart Card into the commercially available CAM (Conditional Access Module).
2
Insert the CAM into the CI (Common Interface) slot of this unit.
TV service encryption is automatically cancelled and the service can be viewed or recorded.
§
≥
When using unencrypted digital terrestrial broadcasts or analogue broadcasts, you do not need to insert CAM. Proceed to STEP 2. (
>
below)
§
The recording might be prohibited by broadcasters.
≥
Before connection, turn off all equipment and read the appropriate operating instructions.
≥
Refer to “Additional connections” (
>
73) for connection using other terminals and connection with other equipment.
≥
Be sure to insert the CAM horizontally into the slot.
≥
Insert the CAM with the correct direction.
≥
For more details, see the manual of the CAM and Smart
Card, or consult the dealer.
≥
The Common Interface supports the modules according to
DVB Specification and CI Plus Specification.
≥
Unplug the AC mains lead before you insert or remove the
CAM with Smart Card. Remove it slowly.
OUT
OUT
AV OUT
AV OUT
DIGITAL AUDIO OUT
DIGITAL AUDIO OUT
(PC
PCM/
M/BITSTREAM
BITSTREAM)
RF
IN
RF
OUT
VIDEO
AUDIO
R
L
AV1
(TV)
OPTICAL
AV2
(EXT)
AC IN
COMMON INTERFACE
COMMON INTERFACE
COMMON INTERFACE
AC IN
AC IN
CI (Common Interface)
slot
2
1
CAM (Conditional Access Module)
Smart Card
This unit’s rear panel
Note
STEP
2
Connection
Using a 21-pin Scart cable
≥
You can use a variety of Q Link functions by connecting the unit to a Q Link compatible television (
>
39).
≥
You can enjoy high-quality viewing by connecting the unit to an RGB compatible television (
>
86).
“AV1 Output” in the Setup menu (
>
69)
When the unit is not to be used for a long time
To save power, unplug it from the household mains socket. This unit consumes a small amount of power, even when it is turned off.
[approx. 0.3 W (“Power Save in Standby” is activated and “RF OUT ( Aerial Signal )” is set to “Off”.)]
Connecting a television
Required setting
OUT
OUT
AV OUT
AV OUT
DIGITAL AUDIO OUT
DIGITAL AUDIO OUT
(PC
PCM/
M/BITSTREAM
BITSTREAM)
RF
IN
RF
OUT
VIDEO
AUDIO
R
L
AV1
(TV)
OPTICAL
AV2
(EXT)
AC IN
COMMON INTERFACE
COMMON INTERFACE
COMMON INTERFACE
VHF/UHF
RF IN
AV
4
3
2
1
2
A
V
To the terrestrial aerial
Television’s rear panel
Aerial cable/
CATV coaxial
cable
This unit’s rear panel
To household mains socket
(AC 220 to 240 V, 50 Hz)
Fully wired 21-pin
Scart cable
AC mains lead
(supplied)
Connect only after all other connections are
complete.
“AV2 Input” setting in the Setup menu
(
>
70)
Required setting
21-pin Scart
cable
Cooling fan
Connecting a terminal other than the
21-pin Scart terminal (
>
7, 73)
RF coaxial cable
(supplied)
Connect the unit directly to the
television
If you connect the unit through an AV
selector or video cassette recorder to
the television, video signal will be
affected by copyright protection systems
and the picture may not be shown
correctly.
≥
When connecting to a television
with a built-in VCR
Connect to the input terminals on the television side if
there are both television and VCR input terminals.
Television
VCR
This unit
DO NOT
Common Interface (CI) slot
In order to view or record encrypted CATV services,
you must insert a certified CAM and Smart Card
into this slot. (
>
above)
Cable
Digital satellite
receiver’s rear panel
For viewing digital satellite broadcasts,
connect this unit with a digital satellite
receiver before connecting the AC
mains lead.
DMREX84C-VQT3C69_eng.book 6 ページ 2010年12月10日 金曜日 午後4時45分