Before Use
12
Connect an amplifier with a built-in decoder
with these logo marks.
≥
Use an optical digital audio cable.
≥
Change the settings in “Digital Audio Output” (
l
44).
≥
You cannot use DTS Digital Surround decoders not suited to DVD.
≥
Even if using this connection, output will be only 2 channels when
playing DVD-Audio
This unit has DVD/VHS COMMON output terminals which are
common to both DVD and VHS, and DVD output terminals which are
exclusively used for DVD.
≥
For DVD/VHS COMMON output terminals, both DVD and VHS
outputs can be switched.
≥
The DVD output terminals can only output the DVD signal.
Preparation
≥
Press [DVD].
[1]
While stopped
Press [FUNCTIONS].
(
l
47)
[2]
Select “SETUP” with [
3
,
4
,
2
,
1
] and press
[ENTER].
[3]
Select “Set Up” with [
3
,
4
] and press [
2
,
1
].
[4]
Select “DVD/VHS Output” with [
3
,
4
] and press
[ENTER].
[5]
Select “Automatic” or “Manual” with [
3
,
4
] and
press [ENTER].
Connecting amplifier or system component
∫
To enjoy multi-channel surround sound on
DVD-Video (digital connection)
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COMPONENT VIDEO OUT
(480P/480I)
Y
P
B
P
R
R - AUD
R - AUD
DVD OUT
OPTICAL IN
(1)
(3)
(4)
(5)
(2)
(1) Rear panel of this unit
(2) Insert fully, with this side
facing up. (Do not bend when
connecting.)
(3)
Optical digital audio cable
(not supplied)
(4) To optical digital input
(5) Amplifier’s rear panel
Dolby Digital (
l
44
)
This is a method of coding digital signals developed
by Dolby Laboratories. Not only stereo (2 channel)
audio, these signals can also be 5.1-channel audio.
A large amount of audio information can be
recorded on one disc by this method.
DTS Digital Surround (
l
44
)
This surround system is used in many movie
theatres around the world. The separation between
channels is good and the compression ratio is low,
so realistic sound effects are possible.
DTS sound tracks are produced with the assumption
that all channels will be used.
∫
Connection to a stereo amplifier
(analog connection)
OPTICAL
ITAL AUDIO OUT
CM/BITSTREAM)
COMPONENT VIDEO OUT
(480P/480I)
P
B
P
R
R - AUDIO - L
VIDEO
R - AUDIO - L
VIDEO
S-VIDEO
DVD OUT
DVD/VHS COMMON OUT
R L
AUDIO IN
(4)
(5)
(2)
(3)
(1)
(1) Rear panel of this unit
(2) To AUDIO OUT (L/R)
(3) Audio cable (not supplied)
A
Red (R)
B
White (L)
(4) Audio input (L/R)
(5) Amplifier’s rear panel
DVD output and DVD/VHS output
≥
Even if “Automatic” is selected in “DVD/VHS Output” on
“Set Up” Menu (
l
43), the desired output may not be selected
depending on the operation. In this case, press [DVD/VHS
OUTPUT] on the remote controller to switch manually.
≥
When the Video is switched from DVD to VHS or vice versa,
the audio volume may suddenly increase or decrease. This is
because when the audio output of this unit is connected to the
TV or other, the audio output of the DVD is generally lower.
When you increase the volume level of the TV or the amplifier
to play back DVD audio, reduce it when playback is finished.
R - AUDIO
OPTICAL
DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COMPONENT VIDEO OUT
(480P/480I)
Y
P
B
P
R
R - AUDIO - L
VIDEO
S-VIDEO
DVD OUT
R - AUDIO - L
VIDEO
DVD/VHS COMMON OUT
DVD/VHS COMMON output
DVD output
PP-Sample.book 12 ページ ２００４年４月８日 木曜日 午後３時４５分
