background image

6

(EN)

Energy Saving Function

Saves energy for existing air conditioners by reducing energy waste.

Temperature Auto Return 

*1

 

Restores the changed temperature to the originally set temperature 
automatically after a speci

fi

ed time has elapsed.

Cooling only when there is a visitor

Temperature Range Restriction 

*1

 

Restricts the temperature range that can be set.

Temperatures outside the range cannot be set.

Auto Shut-off Setting 

*1

 

When the operation is stopped at a speci

fi

ed time and resumed afterwards, the 

unit detects the operation status at regular time intervals and stops operation 
automatically.

Repeat OFF Timer 

*1

 

Every time operation is performed, the unit stops operation after a certain 
period of time.

Recommended for less frequent use and for short-period use at one time.

Peak cut Setting 

*1

 

(Gas heat pump saving *

2

)

 

Reduces the maximum power that can be output using the condition selected 
at the time of installation.

The 3 modes below are selectable.

Reduces the power by specifying time zones.
(Specify the 
maximum 
power for each 
time zone.)

Reduces the power by specifying time 
zones.

Large

Small

11 : 00

13 : 00

16 : 00

19 : 00

Time zone to reduce the operation capacity

Reduces the power that can be output using 
external equipment.

Energy saving

Ratio of 
output to 
the 
maximum 
capacity
95%

Send a signal

Large

Small

11 : 00

Energy saving

Large

Small

Schedule peak cut

Schedule energy saving (Efficient operation *

2

)

External input peak cut

*1:          is displayed on the setting screen. 

(Energy saving function indication)

*2: When using a gas heat pump air 

conditioner

Summary of Contents for CZ-64ESMC3

































































Reviews: