background image

20

(EN)

Weekly Timer Overview

You can set a weekly operation schedule.

• The operation ON/OFF schedule or temperature setting schedule can be set by setting the day 

and time (e.g. Setting the operation start time to 8:00 a.m. from every Monday to Friday.).

How to set (Overview)

(See P.21 for setting procedure)

• Select 

“Day”

• Select 

“Time”

• Select 

“Prohibit R/C [

]”

 

for the remote control

•  

Select 

“Temperature”

•  

Select 

“Operation mode”

* Select 

“Operation”

Combination examples

1.  Stop operation earlier on “No-overtime work 

day”

8:00

17:00

8:00

22:00

Operating

Operating

Stop

Start

Weekday

No-overtime 

work day

• The setting registered for 1 day can be copied to other days. 

(P.24)

2. Set the temperature higher after the 

fi

 xed time.

8:00

22:00

17:00

Operating (26 °C) (28 °C)

Start & 

TEMP

Stop

TEMP

3. Stop operation during lunch break.

8:00

22:00

12:45

12:00

Operating

Operating

OFF

Stop

Start

Start

Stop

4. This Thursday is a holiday.

The timer can be disabled only for the speci

fi

 ed days with the 

registered schedules kept. (P.25)
• Disable (

) the timer of the speci

fi

 c Thursday which falls on 

a holiday. 

• Enable (

) the timer after the holiday is over.

Summary of Contents for CZ-64ESMC3

































































Reviews: