Panasonic AIG707WCL1G2 User Manual Download | Manualshive

Page: 20 / 54

background image

Installation

and Wiring

3.1.5 GT707 Installation Method

Secure the GT to the installation panel using the fittings and screws (4 sets/per unit) provided

with the unit.

PROCEDURE

1.  Place the GT unit in the installation panel.
2.  Insert the fittings into the grooves of the GT unit, and slide them to be fixed.
3.  Tighten the screws [M3 (Length: 16 mm)] to secure the GT unit to the

installation panel.

(Enlarged view)

•

The cross slot screwdriver of #2 must be used.

•

The tightening torque of the screw [M3 (Length: 16 mm)] should be 0.2 to

0.3 N·m. Tightening the screws too hard can cause deformation of the front

panel, so that the touch switches will not function properly.

3-4

«
...
18
19
20
21
22
...
»

Summary of Contents for AIG707WCL1G2























































Reviews:

No comments

Related manuals for AIG707WCL1G2

Brand: Ebird Pages: 11

Brand: LaCie Pages: 4

Brand: Rae Pages: 4

Brand: Raymarine Pages: 12

Brand: Wahoo Pages: 5

Brand: Angel Pages: 2

5.8" TFT LCD Wide color monitor

Brand: Farenheit Pages: 4

Brand: A1 Touch Pages: 14

Brand: ViewSonic Pages: 2

Brand: Mobi Technologies Pages: 9

Brand: Zenith Pages: 64

Brand: NEC Pages: 2

Brand: Siko Pages: 12

Brand: Hanns.G Pages: 25

Brand: Citizen Pages: 60

Brand: V7 Pages: 1

Brand: Ctl Pages: 8

ecomatDisplay CR1152

Brand: IFM Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands