Panasonic AFP7PSA1 User Manual Download Page 101

Page: 101 / 109

8.2

Power Supply Unit Specifications

8-25

8.2.2 Performance Specifications

Items

Description

Rated input voltage

100 to 240V AC

Input voltage amplitude range

85 to 264V AC

Rated frequency

50 / 60 Hz

Frequency range

47 to 63 Hz

Phases

Single-phase

Input current

AFP7PSA1: 0.75A
AFP7PSA2: 1.25A

Inrush current

40 A (0-P) or less; Cold start

Leakage current

0.75 mA or less between AC input and protective earth terminals

Input

Momentary power drop time

10 ms or more

Rated output current (Note 1)

AFP7PSA1: 24V DC, 1A
AFP7PSA2: 24V DC, 1.8A

Output

Overcurrent protection (Note 2)

Guaranteed lifetime

27,000 hours (+55



Terminal screw

Built-in (Replacement is not available)

(Note 1) Use the unit within the rated output current.

(Note 2) Oscillation is stopped during protected operation.

To recover, turn off the input and then on again. Wait at least 180 seconds before turning the input on again.

8.2.3 Alarm Output Specifications

Items

Description

Contact capacity

1A 30V DC

Alarm contact operations

Contact OFF at CPU alarm occurrence

Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]

Summary of Contents for AFP7PSA1














































































































Search results

Summary of Contents for AFP7PSA1

Reviews:

Brands by name

Popular brands

Panasonic AFP7PSA1, User Manual

Search results

Summary of Contents for AFP7PSA1

Reviews:

Brands by name

Popular brands