manualshive.com logo in svg

Panasonic AFP0HC32EP, User Manual, Page: 32 / 102

Share
Download
Panasonic AFP0HC32EP User Manual Download Page 32

 

Setting Procedure 

3-6 

 

3.2.3  EtherNet/IP Basic Configuration 

Make the EtherNet/IP basic configuration. The following procedure is explained on the 

assumption that the EtherNet/IP setting screen has been activated. 

PROCEDURE

 

1.  Select "Setting" > "EtherNet/IP Basic Configuration" from the menu bar. 

The EtherNet/IP Basic Configuration dialog box appears. 

 

2.  Change the settings of "Auto Allocation" and "RUN/IDLE bit operation of 

cyclic communication" as necessary. 

In this example, "Auto Allocation = No", and "RUN/IDLE bit operation of cyclic 

communication = Normal". 

3.  Press the [OK] button. 

KEY POINTS

 

•

 

When allocating devices manually, set "Auto Allocation" to "No". 

•

 

For performing operation check, set "RUN/IDLE bit operation of cyclic 

communication" to "Limited". When selecting "Normal", the RUN/IDLE bit of 

the FP0H does not turn "ON" unless the communications with all the targets 

registered in the scan list are established. 

Summary of Contents for AFP0HC32EP







































































































Reviews:

No comments