Pan Acoustics P SW-208 SP AES Manual Download

Page: 2 / 22

V 1.0

Page 2 of 22

General information

Manual Pan Subwoofer Series

P SW-208 | SP

P SW-208 | SP | AES

P SW-208 | SP | D

Version: 1.0

Language: EN

Doc. No.: 2021_01328

DANTE

is a registered trademark of Audinate Pty Ltd and describes a digital audio network.

This document must be kept with the product or in a safe place so that it is available when

needed.

If the product is resold, the document must be handed over to the new owner in printed or electronic

form.

Pan Acoustics reserves the right to change / update the document without prior notice. The latest

version of this document can be downloaded from the Pan Acoustics website.

Pan Acoustics GmbH

Schweigerstr. 13d | 38302 Wolfenbüttel

Tel: +49 (0) 5331 900 95 70 | Fax: +49 (0) 5331 900 95 79

E-mail: [email protected]

Summary of Contents for P SW-208 SP AES























Search results

Summary of Contents for P SW-208 SP AES

Reviews:

Related manuals for P SW-208 SP AES

Brands by name

Popular brands

Pan Acoustics P SW-208 SP AES, Manual

Search results

Summary of Contents for P SW-208 SP AES

Reviews:

Related manuals for P SW-208 SP AES

Brands by name

Popular brands