Paloma PJC-W18FR Installation Instructions Manual Download Page 9

 

 

Do  not  use  this  heater  in  areas  where  spray  painting  is  taking  place  or  in  areas  such  as  hairdressers 
where there may be lots of fluff and dust or where aerosols may be used. 

 

All replacement parts must be approved Paloma spare parts. 

 

This  heater  may  circulate  large  volumes  of  air.  If  the  air  in  the  room  contains  any  cigarette  smoke  or 
cooking vapours, it may affect the appearance of carpets, furniture and drapes, etc.  

 

Clean the air filter regularly (at least once a week). 

 
 
 
 
 
 
 
 

 

Do not move the heater during operation. 

 

Do not use for any other purpose other than for heating. Must only be used as a space heater. 

 

Do not touch the  warm air outlet during operation.  Supervise  young children or infirm persons  near the 
heater. Also ensure that children do not play with this appliance. 

 

Do not sit, stand or lean on the heater. 

 

Do not insert your fingers into the louvres or the air inlet of the heater. 

 

Do  not  cut  the  electrical  cord  to  extend  the  lead.  Install  the  heater  where  the  original  electrical  cord 
reaches a wall socket. 

 

Do not unplug or shut down during operation. This may cause overheating. 

 

Do not place the heater near an opening door. The heater could be knocked over.  

 

Do not touch the electric plug with wet hands as this could cause an electric shock. 

 

Do not pull the electrical cord to unplug as this could break the cord and start a fire. 

 

Place  a  flat  board  for  stability  when  placing  the  heater  on  soft  or  thick  carpet.  Placing  directly  on  to  a 
carpet may discolour the carpet. 

 

Ensure that recommended clearances are maintained at all times. 

 

This  heater  is  designed  for  domestic  household  applications  only.  Using  this  heater  in  commercial 
applications will shorten its life significantly.  

 

In case of thunderstorms, cease operation and unplug the electrical cord. 

 

Do not use sprays containing silicon in the vicinity of the heater. It damages the oxygen depletion safety 
device. 

 

Do not install in a place where the heater may be affected by wind. The flame could be blown out by a 
strong wind. 

 

Do not place articles on or against or in front of warm air outlet or air filter of this appliance. 

 

If the heater is shut off by the oxygen depletion safety system, please ensure you ventilate the room 
immediately for satisfactory combustion.  

 

Prior to operation of the unit please ensure that the gas hose is removed from the holding clips, uncoiled 
and installed into your bayonet fitting without any kinks in the hose.  
 

 
 
 
 
 
 
 
 
 
 
 
 
 

Caution 

Summary of Contents for PJC-W18FR

























Reviews: