background image

10

MISO 48 FIREBOWL Match-lit | Installation & Owner's Manual

STOP!  

Review the safety information 

on pages 1, 2 and 10 of this 

manual.

Use only your hand to push 

in or turn the gas control key. 

Never use tools. If the key will 

not push in or turn by hand, 

don’t try to repair it, call a 

qualified service technician. 

Force or attempted repair 

may result in a fire or 

explosion.

Please ensure that you 

are familiar with the safe 

operation of the fire pit 

controls before replacing the 

instructional control knob 

with the Paloform key.

The control key/knob is 

meant to fit tight and be left 

in place. Remove only for 

winterization.

The gas valve has three positions: PILOT, ON and OFF.

To light your fire pit, you first light the pilot flame, then turn on the gas to main burner.

Before lighting, allow five minutes for any gas in the vicinity to dissipate. (LP gas, 

which is heavier than air, may require forced ventilation).
1.  Insert the control key (or control knob). Make sure the "half-moon"-shaped hole in 

the end of the key and the valve stem are aligned.

2.  The key should turn freely 90°. Turn the key to the PILOT position (clockwise until 

it stops)

3.  Push the control key in until it stops, and hold in this position.
4.  Apply a flame to the lighting port with a barbecue lighter. The pilot flame will 

ignite.

5.  Continue to hold the key down for up to thirty seconds after lighting the pilot.
6.  When the control key is released, the pilot flame should continue to burn (if the pilot goes out, repeat the above steps).
7.  Rotate the gas control key from PILOT to ON position (full counterclockwise position) to supply full flow to main burner.
Failure to turn the control key to the full ON position will reduce the flow and could result in poor ignition of main burner.
8.  To extinguish main burner, rotate the gas control key clockwise to the PILOT position.
9.  To extinguish pilot, push the control key in slightly and turn to the OFF position (fully clockwise).
NOTE: We do not recommend leaving the fire pit unattended with the pilot lit. Please turn to the OFF position.

LIGHTING YOUR FIRE PIT

VALVE POSITIONS

PILOT

Push key in PILOT position to start the 

flow of gas to the pilot. Light the pilot 

while holding the key in 

ON

Turn the key 90° counter-clockwise to 

turn on the main burner.  To turn the 

main burner off, turn clockwise 90° 

back to the PILOT position

To turn the pilot off, push slightly and 

turn clockwise 90° to the OFF position.

OFF

Summary of Contents for MISO 48















Reviews: