background image

Safety  Precautions

Note!

It is required to read the Safety precautions in detail before 
operation. The precautions listed below are all-important for 
safety, please obey without fail.

Make sure  that the fixed ground wire in the building is securely connected to earth.

Wiring tasks should be carried out by qualified electricians only, in addition, they should check the safety conditions 
of power utilization, for example, check if the line capacity is adequate, and check if the power cable is damaged.

Users must not install, repair or relocate the unit.

Improper treatment might lead to the accidents e.g. personal injury caused by fire, electrical shock or unit's falling-
off, and water leakage in the machine. Please contact professional repair and service department of local dealer.

In case the leaked gas is congregated around the machine, there might be the risk of explosion.

The unit  shall not be installed at a spot with potential hazard of leakage of inflammable gas.

If the foundation is unstable, the outdoor unit may drop and cause a casualty accident. so this must be validated carefully.

Make sure that the foundation of installation is stable.

If no electric leakage protection switch is fitted at the beginning of the electric supply, it maybe cause electric shocks or 
fires.

Make sure that the electric leakage protection switch is fixed.

Before cleaning, shut off the electric supply of the unit firstly to avoid injuries caused by fan in operation.

Do not rinse the unit by water because the rinsed unit  may cause electric shock.

Please observe the follow items when cleaning the unit.

Make sure to shut off the electric  supply before maintaining the unit.

Please do not insert fingers or sticks into air outlet or air inlet.

The machine must be transported and stored vertically.

General 

If any abnormity occurs in the unit (such as burned taste inside the unit), cut off the power supply immediately, 
and contact professional repair and service department of local dealer.

The machine must be transported and stored vertically.

Transport and storage

2

Summary of Contents for H Series





















Reviews: