Palfinger MiniFix 1100 Owner'S Manual Download Page 6

Page: 6 / 38

MiniFix 1100/1320

Owner’s Manual

Rev. 1.3

- 6 -

Safety Information

This manual follows the

Guidelines set forth in “ANSI Z535.4-2007” for alerting you to possible hazards and

their potential severity.

! DANGER

indicates an imminently hazardous situation which, if not avoided,

will result

in death or serious

injury.

! WARNING

indicates potentially hazardous situation which, if not avoided,

could result

in death or serious

injury.

! CAUTION

indicates a potentially hazardous situation which, if not avoided,

may result

in minor or

moderate injury.

CAUTION

without the safety alert symbol is used to address practices not related to personal injury.

(

In this manual it is used to alert the user to potentially hazardous situation which, if not avoided, may result

in property damage.)

NOTICE

without the safety alert symbol is used to address practices not related to personal injury.

(In this

manual it is to alert you to special instructions, steps, or procedures.)



Always be aware of your surroundings.



Wear eye protection at all times during installation.



Ear protection and gloves should be used when necessary.

The maximum loads must be observed and followed!

Summary of Contents for MiniFix 1100







































Search results

Summary of Contents for MiniFix 1100

Reviews:

Related manuals for MiniFix 1100

Brands by name

Popular brands

Palfinger MiniFix 1100, Owner'S Manual

Search results

Summary of Contents for MiniFix 1100

Reviews:

Related manuals for MiniFix 1100

Brands by name

Popular brands