Palfinger MBB C 500 VAN Operating Instructions Manual Download Page 115

Page: 115 / 196

115

Bringing Down the Platform



Press the pushbutton

(43)

and keep it pressed until the

platform is adjusted flush to the ground.

After the platform has touched the ground it tilts and adjusts
to the ground.

Lifting the Platform



Press the pushbutton

(42)

and keep it pressed until the

platform has reached the loading position.

Before the platform is lifted it tilts to the horizontal position.

Lifting the Scissors



Press the pushbutton

(44)

and keep it pressed until the

platform has reached the loading position.

Bringing Down the Scissors



Press the pushbutton

(45)

and keep it pressed until the

platform has reached the loading position.

Betriebsanleitung_Hubladebuehnen_EN.book Seite 115 Donnerstag, 15. August 2019 4:04 16

Summary of Contents for MBB C 500 VAN





































































































































































































Search results

Summary of Contents for MBB C 500 VAN

Reviews:

Related manuals for MBB C 500 VAN

Brands by name

Popular brands

Palfinger MBB C 500 VAN, Operating Instructions Manual

Search results

Summary of Contents for MBB C 500 VAN

Reviews:

Related manuals for MBB C 500 VAN

Brands by name

Popular brands