Palfinger MBB C 500 VAN Operating Instructions Manual Download Page 113

Page: 113 / 196

113

Optional Operating Method: Hand Cable
Control with four Pushbuttons for
MBB C 750 SX

44
45

Pushbutton: lift

Pushbutton: lower

Pushbutton: lift scissors

Pushbutton: lower scissors

DANGER!

Risk of accidents and injury!

If the instructions in chapter "General Information" are not ob-
served during operation of the tail lift, personal injuries and
material damage can occur.



Before operating the tail lift, read chapter “General Opera-
tion” from p. 26.

Betriebsanleitung_Hubladebuehnen_EN.book Seite 113 Donnerstag, 15. August 2019 4:04 16

Summary of Contents for MBB C 500 VAN





































































































































































































Search results

Summary of Contents for MBB C 500 VAN

Reviews:

Related manuals for MBB C 500 VAN

Brands by name

Popular brands

Palfinger MBB C 500 VAN, Operating Instructions Manual

Search results

Summary of Contents for MBB C 500 VAN

Reviews:

Related manuals for MBB C 500 VAN

Brands by name

Popular brands