background image

 

8

PREPARATOR

®

 SETUP

 

 

 

SAFETY FIRST!! READ AND UNDERSTAND THE SAFETY INSTRUCTIONS (pages 

2-5 of this manual) BEFORE BEGINNING ANY PREPARATOR

® 

SETUP 

 
 

SKID SHOE ADJUSTMENT 
 
Before adjusting the skid shoes, determine what the soil conditions are and what type of operation is to be performed.  
Remember that each time the soil conditions or operation type changes, the skid shoes may need to be repositioned. 
 
Soil Conditions 

 HARD: 

This is highly compacted soil, usually inorganic (clay).  Any soil that has been subject to vehicle 
or construction traffic would also be considered this soil condition. 

 MEDIUM: 

This is untilled soil that has not been subject to compaction devices or traffic. 

 LOOSE: 

This soil that has received a rough tillage pass of some type, but is still lumpy and coarse. 

 VERY LOOSE: 

This soil that has been tilled to a fine texture. 

 
Operation Type 

 ROCK 

COLLECTION: 

Collecting large rocks and debris that are resting on the soil surface. 

 FOLIAGE 

REMOVAL: 

Uprooting and collecting foliage that is growing or has been growing on the soil 
surface. 

 SOIL 

TILLAGE: 

Tilling the soil to create a looser soil condition. 

 ROUGHING: 

Scarifying, raking rocks, debris, & foliage, and filling depressions in tilled or untilled 
soil. 

  FLAT MODE ROUGHING: 

Roughing with the shroud parallel to the ground. 

 ANGLED 

MODE 

ROUGHING: 

Roughing with the shroud at an angle to the ground surface. 

 FINISHING 

PASS: 

Collecting small rocks and debris that are in or on the soil surface. 
 

Skid Shoe 

Adjustment Slots 

Rotor Tooth Depth 

Below Skid Shoe 

Operation on 

Soil Condition 

(Initial settings only. Workability, moisture, 

experience, etc. affect settings.) 

 
 
 

 

 

 

 

 

 

 

(-) 5/8”   

Finishing Pass on Very Loose soil. 

      Foliage 

Collection 

 
 
 
 

 

 

 

1/4” 

 

Flat Mode Roughing on Medium or Loose soil. 

      Finishing 

Pass 

on 

Loose 

soil. 

 
 
 
 

 

 

 

1-1/8”   

Rock Collection on Hard or Medium soil. 

      Soil 

Tillage 

on 

Medium 

soil. 

      Flat 

Mode 

Roughing 

on 

Hard 

soil. 

      Finishing 

Pass 

on 

Medium 

soil. 

 
 

 

 

 

2” 

 

Foliage Uprooting on Hard or Medium soil. 

 

 

 

 

 

 

Angled Mode Roughing on Hard, Medium, or Loose soil. 

      Soil 

Tillage 

on 

Hard 

soil. 

 
 
 
 
 

 

Summary of Contents for FFC LAF3554

























Reviews: