background image

 

 
 

Swing device 

 

Grain thrower T 2 might be equipped with manual or electric swing device.   

 

Manual

 

 

Setting of throw direction is done manually. The equipment is here fixed with a plug-in bolt in the perforated 
bar of the turntable. It must be controlled that the plug-in bolt is led through the perforated bar, since the 
equipment will otherwise move uncontrolled at both sides. 

 

 

Electric

 

 

Connecting and disconnecting of an automatic swing device takes place in the control box. Emergency stop 
buttons are placed on the hopper. 

 

The electric swing area can be changed by adjusting switch 1 or/and switch 2  

 

The switches are not to be removed, since they also serve as emergency stop buttons (safety switch). If the 
switches are removed, the guarantee lapses. 

 

Take care that swing device and switches are not standing in the grain. Switches are cleaned once daily. The 
engine should be checked regularly based on circumstance. 

 
 

Disconnecting of safety switch for swing movement

 

 

If the safety switch is activated, the disconnecting takes place as follows:  

 

1.

 

The switch for manual/automatic (illustration 2 pos. 1) is set at manual.   

 

2.

 

Switch 2 (illustration 2 pos. 2) is activated, and the equipment is moving away from the safety switch.  

 

3.

 

Switch 1 (illustration 2 pos. 1) can again be set at automatic. The equipment is ready for operation again.  

 

Starting-up

 

 

NOTE prior to each starting-up !

 

 

1.

 

No person is allowed to stay in the operating and throwing area of the grain thrower. 

Materials and 

material remains might cause serious injuries. Be aware that small parts or gravel that has stuck to the 
equipment or the belt might loosen and be thrown out of the equipment in a high speed. This might cause 
serious injuries to persons and damage to equipment parts.  

 

2.

 

When setting and readjusting drums, belts and bearings you must wear appropriate protective clothing. In 
this case a safety area of 50 m in the throwing direction must also be observed. 

 

 

3.

 

Prior to starting-up you must control that there is no materials or loose parts in the hopper. 

 
 
 
 

Summary of Contents for Grain Thrower T 2










Reviews: