background image

 

 

ADF SERIES™ OPERATION MANUAL 

 

SECTION 8

Remote Control Programming

 

Entire Contents Copyright 

 2018 by Pacific Power Source, Inc. (PPS) • All Rights Reserved • No reproduction without written authorization from PPS. 

ADF Series Power Source Operation Manual 

Page 233 of 349

 

Command Syntax 

SYSTem:COMMunicate:LAN:HOST:CONFigured

 

Description 

Sets the network host address. The host address is the portion of the 

address used to identify hosts (any device requiring a Network 

Interface Card, such as a PC or networked printer) on the network. 

The network ID, by contrast, is the portion of the address that refers 

to the network itself. 

Parameters 

ddd.ddd.ddd.ddd  (four octets ranging in value from 0 to 255 

representing one 16 bit unsigned integer value each. 

Parameter Format 

<cr> 

Example 

SYST:COMM:LAN:HOST 132.18.21.0 

Query Format 

SYSTem:COMMunicate:LAN:HOST:CONFigured?

 

Returned Data Format 

<cr> 

Query Example 

SYST:COMM:LAN:HOST:CONF? 

132.18.21.0 

 

Command Syntax 

SYSTem:COMMunicate:LAN:PASSword

 

Description 

Assign a password to enable or disable LAN communications. This 

feature allows the owner/operator to disable or enable remote LAN 

access or limit functionality over LAN. 

Note:

 There is no query format for this command so the password 

code cannot be queried back. 

Parameters 

Four digit passcode 

Parameter Format 

<nr1? 

Example 

SYST:COMM:LAN:PASS 1234 

 

Command Syntax 

SYSTem:COMMunicate:LAN:PORT

 

Description 

Sets LAN interface port address. For SCPI message communications, 

the standard port number is 5025. 

Parameters 

1024–49151, default = 5025 

Parameter Format 

<nr1> 

Example 

SYST:COMM:LAN:PORT 5025 

Query Format 

SYSTem:COMMunicate:LAN:PORT?

 

Returned Data Format 

<nr1> 

Query Example 

SYST:COMM:LAN:PORT? 

5025 

 

Command Syntax 

SYSTem:COMMunicate:LAN:PORT:TELNET

 

Description 

Sets the port address for TELNET protocol 

Parameters 

1024–49151, default = 5024 

Parameter Format 

<nr1> 

Example 

SYST:COMM:LAN:PORT:TELNET 5024 

Query Format 

SYSTem:COMMunicate:LAN:PORT:TELNET?

 

Returned Data Format 

<nr1> 

Query Example 

SYST:COMM:LAN:PORT:TELNET? 

5024 

 

Summary of Contents for ADF Series






























































































































































































































































































































































Reviews: