background image

12 SUPER-SD1 

071111-20

Optional 
Blower

The optional blower kit (kit #WODC.BLOW) is equipped 
with a three prong power cord and may be installed at 
any time. Follow installation instructions supplied with the 
kit. Route power supply cord away from heater.

Electrical rating:  115 volts A.C.-1.02 amps.
Fan output rating:  125 CFM

Blower Operation

Proper blower speed matched with air control setting 
will ensure peak performance from your stove. Operate 
as follows:
 

- Air control set to "L" (low), operate blower speed 
control on "Low".

 

- Air control set between "L" and "H" (low and high), 
operate blower speed control at desired setting.

Automatic:

  To operate the blower automatically, set the 

rocker switch on the side of the fan housing to "Auto" 
and set the speed control to desired setting. This will al-
low the fan to turn on as the stove heats up to operating 
temperature. It will also shut the blower off after the fi re 
has gone out and the unit cooled to below a useful heat 
output range.

Manual:

  To manually operate the blower, set the rocker 

switch to "Man" and set the speed control to desired set-
ting. This will bypass the sensing device and allow full 
control of the blower.
Switching from "Auto" to "Man" or selecting speed may 
be done anytime.

Optional Outside Air Adaptor

The adaptor is only required if the blower kit is to be in-
stalled and outside combustion air to be ducted to rear 
of pedestal.

Installation:

Remove blower kit if already installed.  Place adaptor with 
the 4" round hole facing up and opposite end covering 
the room air knockout hole on the back of the pedestal.  
Mark attachment holes on pedestal base and drill with 
1/8" bit.  Attach with #8 x 1/2" screws and reinstall fan.  
Combustion air duct from outside can now be attached 
to the 4" round collar.

Summary of Contents for SPECTRUM CLASSICDESIGN-D





















Reviews: