background image

071111-20 

SUPER-SD1 5

Super 27 - Pedestal Model

Spectrum

Super 27 - Leg Model

Spectrum Classic

2)  Secure in place with 1" x 1/2" bolts previously re-

moved.

3)  Carefully place the unit in the upright position.

Leg Kit

1)  With the unit on its back, align the ash drawer enclo-

sure mounting holes (removable cover facing up) with 
the holes on the stove.

2)  Position the legs over top of the same holes on the 

stove.

2)  Secure in place with 1" x 1/2" bolts previously re-

moved.

3)  Carefully place the unit in the upright position.

- Super 27 only -

Assembly

Crate Removal

1)  Carefully remove wood top and supports.
2)   Remove plastic cover.
3)  Using a 7/16" wrench, remove lag bolts that secure 

stove body to bottom pallet.

4)  Place stove body carefully on its back.
5)  Using two 3/4" wrench, remove 1" x 1/2" bolts and 

save for later use.

6)  Remove pallet retaining brackets from stove bottom.

Optional Ash Cleanout System 

-(Install 

fi rst)

1)  With stove body laying on its back, remove the ash 

system hole cover and gasket located under the stove.  
Discard cover plate and gasket.

2)  Inside the stove, remove the two bolts for the ash dump 

from the fi rebox bottom and insert into the brick retainer 
with the fl anges on the the brick retainer pointed away 
from the threads on the bolts.

3)  Replace bolts with brick retainer in the firebox 

 bottom.

4)  Place new gasket provided over existing bolts.
5)  Install ash dump system over gasket and secure with 

two nuts previously removed.

Pedestal Kit

1)  With the unit on its back and the removable cover 

facing up, align the pedestal mounting holes with the 
holes on the stove.\

Summary of Contents for SPECTRUM CLASSICDESIGN-D





















Reviews: