background image

Stinger ELEV8 or HEIGH10

®

 Radio Replacement Kit

for Jeep Wrangler JL  and Jeep Gladiator JT Vehicles

SRK-JW18EH

 © 2020 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.

AAMP Global is not affiliated with FCA US LLC. Jeep® is a registered trademark of FCA US LLC.  The terms 

OEM, Jeep®, Wrangler®, and Gladiator® all terms are used strictly for identification purposes only. It is not 

implied that any part listed is a product of, or approved by, Fiat Chrysler Automobiles.

Pacific Accessory Corporation

Page 3

Rev: v3

Date:100620

Step 3

Step 2

Step 1

Section 1: Disassembly

Part One: Radio Removal

Disconnect the push-to-start button  

and climate control connectors 

from the back of the climate control 

panel and remove.

Grasp the climate control panel at 

the exposed left edge and pull out 

to unclip the left side, then work 

your fingers around the remaining 

edges of the panel to fully unclip 

it.

Pull out at the top of the knee 

bolster to release the retaining 

clips, then work your hands down 

the edges of the knee bolster to 

release the remaining clips and 

remove the panel.

Step 6

Step 5

Step 4

Disconnect the antenna and USB 

connectors from the back of the 

radio, then disconnect the 52-

pin dock-and-lock connector and 

remove the radio.

Remove the four 7mm screws 

securing the radio in place, then 

lift the radio out of the radio 

cavity.

Remove the two 7mm screws 

securing the radio bezel to the 

dash, then pull outward on 

the radio bezel to unclip it and 

remove.

This installation manual will cover the necessary order of procedures to complete the installation 

efficiently and to avoid redoing any steps along the way. The order will be as follows; Disassembly, 

Radio Unit Mounting Preparation, Radio Unit Harness Connections and Preparation, In-Vehicle Harness 

Connections and Preparation, Radio Unit Installation, and Reassembly.

Summary of Contents for Stinger ELEV8















Reviews: