background image

 

39 

 

 

If  the  voltage  is  correct  (43  <V  <55)  disassemble  the  installer  door,  check  the  internal 
battery fuses on the right side of the power board inside the Solar Eclipse 

 

If the fuses are interrupted check the polarity of the connections and replace the fuses (3 
fuses 10 A 6x 32 AT type) 

 

If the fuses are not interrupted contact P800SRL Technical Support 

 

SOLAR ECLIPSE DOES NOT START (first led to the left flashing) 

 

Verify that Solar Eclipse is on (LEDs on) 

 

Check with Software Configurator the presence of voltage from the grid (230 V) 

 

Check  the  correct  installation  and  wiring  of  the  Power  Meter  (make  sure  that  the  cable 
does not get disturbed and use a "twisted" and shielded upper category cable) 

 

Check that the supply fuse is not interrupted (central LED must be fixed) 

 

Check with Software Configurator that the mains voltage is between 210 and 250 V and 
the network frequency between 49 and 51 Hz 

 

Check that there is no alarm in the "trend" table (battery thermal alarm, supply or charger) 

 

Check  in the  "Advanced" tab that there  is  no internal  alarm or  "battery fault".  If  present, 
click on "Reset Charge Fault" 

 

SOLAR ECLIPSE DOES NOT CHARGE BATTERIES (zero charge power in charge) 

 

Verify that Solar Eclipse is "STARTED" (first left LED on) 

 

Connect to interface 485 and start Software Configurator 

 

Shut off loads 

 

Enable the green line "Grid Power" 

in the “Trend” tab and check for negative values < 100 

W (line below zero) 

 

If  the  green  line  is  above  zero  and  the  PV  system  is  producing  more  than  the 
consumption of the user, check the position of the network sensor (Power Meter) 

 

Verify that the "String Power" is greater than 100 W 

 

Verify  that  "String  Voltage"  with  inverter  operating  is  compatible  with  the  number  of 
modules  set  in  the  Software  Configurator  at  configuration  stage  (see  table  8.  eg:  8 
modules set to 30 x 8 = 240 V) 

 

Verify that the battery percentage is < 90% 

 

If  the  "Batt.  Charging" light turns  green  and 

“Battery  Power”  does  not increase  (positive 

values - red Line over Zero) Contact P800 SRL Technical Support 

 

 

Summary of Contents for Solar Eclipse













































Reviews: