background image

ONLINE MANUAL

Scan this QR Code with 

your mobile device to take 

you to the online manual.

Unfolding The Stand

1.  Lay the mitre saw stand on 

the floor with the folded legs 

facing up.

2.  Depress the leg locking button 

and unfold the 2 upper legs 

until the locking button clicks 

into place.

3.   Repeat the same procedure for the other 2 legs.

4.   Lift the stand and flip it into the upright position.

5.   Check that the stand is stable 

and all of the leg locking 

buttons have engaged 

properly.

Folding The Stand

1 pair of legs on the stand must fold in first for the stand to fold flat. 

The legs have not folded into place if the leg locking button does not 

pop into place. The legs should not swing about when the stand is 

picked up if the legs have locked into position.

1.  Turn the mitre saw upside down on the floor with the legs sticking 

up.

2.  Depress the leg locking buttons on the lower pair of legs and fold 

them in.

3.   Repeat the same procedure 

on the other pair of legs.

WARNING! 

KEEP HANDS AWAY FROM MOVING 

PARTS.

1.  Mounting Bar
2.  Fastening Slot
3.  Mounting Bar Handle
4.  Extension Arm Locking Pin

5.  Roller

6.  Material Support Shelf
7.  Upper Leg Locking Pin

8.  Stand Leg

9.  Frame

10. Extension Arm Fastening Knob
11. Lower Leg Locking Pin

12. Extension  Arm
13. Roller  Arm

14. Roller Arm Fastening Knob

MITRE SAW STAND

KNOW YOUR PRODUCT

1. ASSEMBLY

SETUP & PREPARATION

1

2

14

3

4

5

6

9

12

13

7

8

10

11

WARNING! 

THIS STAND IS INTENDED FOR USE 

WITH MITRE SAWS ONLY. DO NOT USE AS A STEP 

LADDER, STEPPING STOOL, STORAGE RACK, ETC. 

OZITO WILL NOT BE LIABLE FOR DAMAGE OR 

INJURY CAYSE BY IMPROPER USE OF THIS UNIT.

Summary of Contents for SCMS-8MSS















Reviews: