background image

Attaching The Extension Arms 

1.  Slide the extension arms into 

the frame.

Note:

 The locking pin on the extension arms should be facing 

inwards towards the centreline of the stand. You will need to depress 

this twice (once when the locking pin reaches the frame and again 

when it pops through the locating hole further in).

2.  Continue sliding the extension arm into the frame until the desired 

length is reached.

3.  Insert a fastening knob into 

the hole on the frame turn 

it clockwise to secure the 

extension arm in place.

4.  Insert a roller arm into the 

collar on the extension arm. 

The material support shelf 

should be facing inwards 

towards the centre of the 

stand.

5.  Insert a fastening knob 

into the bracket and turn it 

clockwise to tighten the roller 

arm into place.

6.  Repeat the same procedure with the opposite extension arm.

Attaching The Mitre Saw Mounts

1.  Depress the mounting 

bar handles and hook the 

opposite end of the mount 

onto the frame of the stand.

2.  Lower the handles onto the 

frame and release them to 

lock the mounting bar into 

place.

3.  Repeat the same procedure with the other mounting bar.

a.

b.

Summary of Contents for SCMS-8MSS















Reviews: