background image

ELECTRICAL SAFETY

WARNING! 

The appliance is not to be used by persons (including children) with 

reduced physical, sensory or mental capabilities, or lack of experience and knowledge, 

unless they have been given supervision or instruction.

Young children should be supervised to ensure that they do not play with the appliance.

• 

 Always ensure the mitre saw base is properly secured to the stand prior to operation.

• 

 Always ensure the stand legs have been locked into place prior to operation.

• 

 Take care when moving the stand especially when a mitre saw is mounted.

• 

 Do not use the stand for any other purpose than what it is intended for.

• 

 Do not use the stand as a stepping stool or ladder.

• 

 Make sure all moving parts are free from interference.

• 

Keep hands clear of all moving parts.

• 

 Ensure the Mitre Saw Stand is set up on firm ground in a stable manner.

• 

Use the Mitre Saw Stand in a dry place protected from the rain.

• 

 Be aware of overbalancing. When a large piece is cut from one end of a job, the remaining piece 

may be heavy enough to over-balance the Mitre Saw Stand. Always ensure the workpiece is well 

supported.

• 

 When transporting the Mitre Saw Stand in a vehicle, always tie it down to prevent movement and 

possible damage.

• 

 Check to make sure that all fixing screws and knobs are tight and all legs are locked into position 

before operation.

• 

 The Mitre Saw Stand must be used only for its prescribed purpose. Any use other than those 

mentioned in these instructions will be considered a case of misuse.

• 

 Ozito shall not be liable for any damage or injury resulting from such cases of misuse.

• 

  Ozito shall not be liable for any changes made to the Mitre Saw Stand nor for any damage resulting 

from such changes.

MITRE SAW STAND SAFETY WARNINGS

 

WARNING!

 

When using mains-powered tools, basic safety precautions, including 

the following, should always be followed to reduce risk of fire, electric shock, personal 

injury and material damage. 

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, 

before operating the tool.

 

Save these instructions and other documents supplied with this tool for future reference.
The electric motor has been designed for 230V and 240V only. Always check that the power supply 

corresponds to the voltage on the rating plate.

Note: 

The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to 

avoid a hazard.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the 

extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead 

not suitable for the power input of the tool or which is damaged or defective may result in a risk of fire and 

electric shock.

The power outlet for the compressor is recommended to be protected by a 30amp residual current device 

GENERAL POWER TOOL SAFETY WARNINGS

WARNING!

 

Read all safety warnings and all instructions. Failure to follow the 

warnings and instructions may result in electric shock, fire and/or serious injury. 

Save all warnings and instructions for future reference. The term “power tool” in the warnings 

refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety 

a.  Keep work area clean and well lit. 

Cluttered or dark areas invite accidents. 

b.  Do not operate power tools in explosive atmospheres, such as in the presence of flammable 

liquids, gases or dust. 

Power tools create sparks which may ignite the dust or fumes. 

c.  Keep children and bystanders away while operating a power tool.

 Distractions can cause you to 

lose control.

2. Electrical safety 

a.  Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any 

adapter plugs with earthed (grounded) power tools. 

Unmodified plugs and matching outlets will 

reduce risk of electric shock. 

b.  Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and 

refrigerators. 

There is an increased risk of electric shock if your body is earthed or grounded. 

c.  Do not expose power tools to rain or wet conditions. 

Water entering a power tool will increase the 

risk of electric shock. 

d.  Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. 

Keep cord away from heat, oil, sharp edges or moving parts. 

Damaged or entangled cords increase 

the risk of electric shock. 

e.  When operating a power tool outdoors, use an extension cord suitable for outdoor use. 

Use of a 

cord suitable for outdoor use reduces the risk of electric shock. 

3. Personal safety 

a.  Stay alert, watch what you are doing and use common sense when operating a power tool. Do 

not use a power tool while you are tired or under the influence of drugs, alcohol or medication.

 A 

moment of inattention while operating power tools may result in serious personal injury. 

b. Use personal protective equipment. Always wear eye protection.

 Protective equipment such as dust 

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce 

personal injuries. 

c.  Prevent unintentional starting. Ensure the switch is in the off-position before connecting to 

power source and/or battery pack, picking up or carrying the tool. 

Carrying power tools with your 

finger on the switch or energising power tools that have the switch on invites accidents. 

d.  Remove any adjusting key or wrench before turning the power tool on. 

A wrench or a key left 

attached to a rotating part of the power tool may result in personal injury. 

e.  Do not overreach. Keep proper footing and balance at all times. 

This enables better control of the 

power tool in unexpected situations. 

f.  Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away 

from moving parts. 

Loose clothes, jewellery or long hair can be caught in moving parts.

g.  If devices are provided for the connection of dust extraction and collection facilities, ensure 

these are connected and properly used. 

Use of dust collection can reduce dust-related hazards.

h.  Do not let familiarity gained from frequent use of tools allow you to become complacent and 

ignore tool safety principles.

 A careless action can cause severe injury within a fraction of a second.

4. Power tool use and care 

a.  Do not force the power tool. Use the correct power tool for your application. 

The correct power 

tool will do the job better and safer at the rate for which it was designed. 

b.  Do not use the power tool if the switch does not turn it on and off. 

Any power tool that cannot be 

controlled with the switch is dangerous and must be repaired. 

c.  Disconnect the plug from the power source and/or the battery pack from the power tool before 

making any adjustments, changing accessories, or storing power tools.

 Such preventive safety 

measures reduce the risk of starting the power tool accidentally. 

d.  Store idle power tools out of the reach of children and do not allow persons unfamiliar with the 

power tool or these instructions to operate the power tool. 

Power tools are dangerous in the hands 

of untrained users. 

e.  Maintain power tools.

 Check for misalignment or binding of moving parts, breakage of parts and any 

other condition that may affect the power tool’s operation. If damaged, have the power tool repaired 

before use. Many accidents are caused by poorly maintained power tools. 

f.  Keep cutting tools sharp and clean.

 Properly maintained cutting tools with sharp cutting edges are 

less likely to bind and are easier to control. 

g.  Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking 

into account the working conditions and the work to be performed. 

Use of the power tool for 

operations different from those intended could result in a hazardous situation.

h.  Keep handles and grasping surfaces dry, clean and free from oil and grease. 

Slippery handles and 

grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

5. Service 

a.  Have your power tool serviced by a qualified repair person using only identical replacement 

parts. 

This will ensure that the safety of the power tool is maintained.

Summary of Contents for SCMS-8MSS















Reviews: